KHMS14 KitchenAid Microwave - Instructions

I loosened the 2 screws at the top, removed the broken-off pieces of the old part, then easily placed the new part and tightened the screws.

The whole process was so easy! It was easy to order the part. It came directly to the house in just a few days.

Thanks.

Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!

E. Robinson

I removed the two screws on the side. Took a putty knife and gently pryed it away from the rest of the door. I took the handle off the old door and put it on the new door. I took the glass and the plastic frame that holds it on off the old door and put it in the new door, I snapped the new door back on and relaced the screws.

First I removed the 2 screws holding the panel on. I then removed the cracked panel. It was held in place by small "catches" built on to thew door. Replacing the new panel was easy, except, I forgot to attach the old handle. I was afraid I would break the new door but it came off with some prying. After replacing the handle, the door went ... Read more on easily.

Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.

I replaced the latch on th ... Read more e microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock

It's a simple repair but costly. Just open the door remove the three screws on the side of door. Now use a small screw driver or metal putty knife to remove the chooker collar around the door " be careful this can easly be broken". Okay now the metal inner door is easier to remove if you slightly bend the tabs up around the door. Look car ... Read more efully you should be able to see where they catch. Once you do that carefully seperate the outter door cover. Careful sometimes it will pop right out and fall. Please no more further repairs needed. Just screw in the new handle push tabs back out on the metal inner door then snap everything back together and reinstall the three screws.

After taking the three screws out of the side of the door, I actually had to get help from my Dad who came over and was able to pry the top corner of the door out of the casing. I was afraid I was going to break the door. Once he got the door pried apart, I was able to replace the handle, clean the entire door and quickly snap it back i ... Read more nto place and then replaced the screws.

Had left the small break in the handle go too long, There fore the screw holes in the door had wallowed out. Had to put some small washers in to bridge the wallowed out screw hole. The ends of the handle had broken off on the end of the mounting screws, had to use pliers and the screwdriver to get the plastic mounts off. There was enoug ... Read more h room for the washers so no additional adaptation was needed. It all went back together very easily.

It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!

The new vent popped right in. Screws easily secured. Same size. Same color. Good as new. Was very simple to do.

Took out 2 phillips screws on top, pulled the old grill out, hooked the tabs on the bottom of the replacement into place, positioned the top of the replacement, and replaced the 2 screws. 5 minutes. NOTE: Save the screws, new ones don't come with the replacement grill.

I really did not have a repair on the microwave just a replacement of the browning pan

First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple

Very easy to replace. A short ladder provides easy access to two small Phillips screws on the top of the existing grill.
Remove and keep these screws to re-use.
Remove old cover and discard.
Fit tabs on the bottom of the new cover into position on microwave and press entire cover securely in place matching the screw hole ... Read more s to the existing microwave.
Replace small Phillips screws securely.
Step back and admire your microwave!

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul