KGST300 KitchenAid Range - Instructions

repair was easy except one part drove me nuts... when putting every thing bacck together i found out that the front glass panel sits on top of the side covers of the door ...looking at the side covers you would think they fit over the top of the front glass...not so the glass edges show and are not covered ... hope this helps someone el ... Read more se

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. ... Read more The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

My husband and I replaced the igniter module, following directions we found online. We removed the old one, replaced it with the new one, and thankfully everything is working great!

Take the door off the oven by sliding out the old hinges that hold the door on to the oven. Put the door up on a protected table so that the hinges can hang down and free of the table. This step will make the job go much more simple. Proceed by removing all visable screws. Make a mental note on how the old hinges are held in and how t ... Read more he door comes apart. Take your time this is not a hard task! I am a homemaker, was taking care of my grandson that day and still accomplished the task in under an hour. The repair people wanted $145.00 labor only to install this part!

The door needs to be removed and laid on a work table. All the screws securing the door parts need to be removed to be able to access the broken glass. This door has 4 layers of glass. Most of the new parts that I was forced to order were not needed and in fact intermediated panel was to large for this door. The inner steel panel was not ... Read more needed either, but I used it as it fit and was clean.

I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.

I let my husband fix this one, so he can tell you about it!

Step one--remove the oven door and place on a padded surface to protect both the door and the surface (table top).

Step 2--remove the screws holding the outer door panel in place.

Step 3--remove the screws holding the middle door panel.

... Read more >Step 4--remove the middle panel of glass then the screws holding the spacer and inner panel of glass.

Step 5--carefully remove the (remains of the) inner panel of glass.

Step 6--replace the inner panel of glass and make sure both sides are clean.

Step 7--reinstall the items removed (in reverse order).

Step 8--replace the oven door onto the range.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I re ... Read more moved the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to inst ... Read more all the replacement, very quick fix.

I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.

real easy one to take care of, when the drawer broke I thought it was more than what it really was, after looking at it and seeing the wheel was gone I ordered the part and it came very quick, drawer is now fixed.

I went online and discovered the repair method and schematic of the range. I removed the spark module after first removing the upper rear panel cover and replaced with the new part module ordered from your company and now the spark module operates all the gas elements when they are turned on thus lighting the gas burners. My mother in law ... Read more was thrilled, as she had been using matches and burning her finger tips,since the original range part malfunctioned. The only problem was the small screw from the original installation was not long enough , so it required some changes to get it affixed to the cabinet side.Thanks for the reasonable price and the right part for the job!!

Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!

Never repaired an oven before, I just used a screwdriver and went slowly taking this over door apart to replace this glass. I just took piece by piece apart until the glass came out and retraced my steps to install the new glass. Sure glad I did this myself, a new convection oven stove would easily set me back 1,500.00 and......save a b ... Read more undle on service call fees.

All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.