The knob skirt or grommet on your range goes around the knob, forming a buffer between it and the range surface. If your knob skirt is damaged, you should consider replacing it. This product is approximately 2 inches in diameter. This part is made of black plastic, and is sold individually. Many of our customers have described this repair...Read more as very easy. To complete the repair, simply remove the burner knob and the old knob skirt, replace it with the new knob skirt and re-attach the burner knob. The product contains four locking tabs that should snap into place easily.
This white knob skirt is located between the glass top and the control knobs of your stove top. The skirt has an outside diameter of approximately 2 inches. The most common reasons to replace the timer knob skirt is if it is cracked or damaged, or if the timer assembly will not advance. This repair is a relatively simple one, but be caref...Read moreul not to snap the plastic clips when you are inserting the new knob skirt into place. This genuine OEM replacement knob skirt is sold individually.
This part is a black plastic knob that is most often used as a burner control knob. This knob allows you to turn the burner on your range or cooktop on, and it allows you to control the temperature of the burner. If your knob is broken, damaged, or lost, this is the replacement part you will need. This knob accepts a d-shaped shaft. To su...Read moreccessfully install this part, line the flat edge of the shaft up with the hole in the knob, then simply press the knob onto the shaft and into place. This knob is sold individually.
The Spark Module WPW10110486 is a genuine OEM replacement part designed for Whirlpool gas ranges and compatible models from KitchenAid, Maytag, Amana, Jenn-Air, and Magic Chef. This module controls the ignition process for the surface burners by generating the electrical spark needed to ignite the gas. It features a terminal configuration...Read more of three 3/16" terminals and six 1/8" terminals. Common signs that this part may need replacement include burners that click without igniting, inconsistent sparking, or no spark at all. For installation, be sure to disconnect both the power and gas supply before beginning. The module should be mounted in the designated control area, with terminals connected according to the appliance’s wiring diagram. Always refer to your appliance’s service manual for model-specific guidance.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
several grate pads fell out/lost /broke during cleaning
61 of 67 peoplefound this instruction helpful.
Sabrina from Mooresville, NC
Really Easy
Less than 15 mins
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It i
... Read mores available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.
Read less
Was this helpful?
Thank you for voting!
There was a crack in the porcelain not letting it spark
23 of 36 peoplefound this instruction helpful.
Billy from Martinsville, IN
Really Easy
Less than 15 mins
Screw drivers
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire. Then just connected the new electrode and place the assy, in the burner.
Was this helpful?
Thank you for voting!
broken ignitor insulation; repeated sparking after burner lit
15 of 21 peoplefound this instruction helpful.
Joe from San Bruno, CA
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers, Wrench (Adjustable)
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!