My Orders
- Home
- KGCR025BAL3
- Instructions
KGCR025BAL3 KitchenAid Cooktop - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
There was a crack in the porcelain not letting it spark
23 of 36 people
found this instruction helpful.
-
Billy from Martinsville, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Was this helpful?
Thank you for voting!
broken ignitor insulation; repeated sparking after burner lit
15 of 21 people
found this instruction helpful.
-
Joe from San Bruno, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Was this helpful?
Thank you for voting!
Replaced Stove knob
9 of 13 people
found this instruction helpful.
-
Robert from Middletown, NJ
- Really Easy
- Less than 15 mins
Removed old one, installed new one
Was this helpful?
Thank you for voting!
Plastic anchor tips broken.
3 of 4 people
found this instruction helpful.
-
Thomas from COLORADO SPGS, CO
- Very Easy
- Less than 15 mins
Removed the broken items and replaced.
Was this helpful?
Thank you for voting!
Spark Ignition Electrode was not sparking properly
5 of 10 people
found this instruction helpful.
-
Wade from Jacksons Gap, AL
- Easy
- Less than 15 mins
-
Pliers
Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the
... Read more
retainer clip.Works great.Thanks Wade
Read less
Was this helpful?
Thank you for voting!
2 control knobs were broken.
2 of 2 people
found this instruction helpful.
-
Sylvia from DELANO, CA
- Really Easy
- Less than 15 mins
I just replaced the broken knobs.
Was this helpful?
Thank you for voting!
Old knobs fell apart
2 of 2 people
found this instruction helpful.
-
Retta from FLOWER MOUND, TX
- Very Easy
- Less than 15 mins
Just put new knobs on. Perfect fit.
Other Parts Used:
Was this helpful?
Thank you for voting!
Grommet broken
2 of 2 people
found this instruction helpful.
-
Ray from POST, TX
- Very Easy
- Less than 15 mins
Good
Was this helpful?
Thank you for voting!
Knob skirt clips (2 of 4) broken
2 of 2 people
found this instruction helpful.
-
John from RAINIER, WA
- Really Easy
- Less than 15 mins
Gently pressed the lower two clips onto my thumbs as I pressed the skirt into the cooktop skirt hole. Be gentle or you can break the new skirt!
Was this helpful?
Thank you for voting!
the little tabs that hold the skirt in the hole break off
2 of 3 people
found this instruction helpful.
-
John from Sequim, WA
- Really Easy
- Less than 15 mins
I pulled the knobs off, lifted the broken skirts out and snapped the new ones in.
Was this helpful?
Thank you for voting!
igniter on top right front burner was shorting out,it would click but not ignite burner
2 of 3 people
found this instruction helpful.
-
Shelly J from KAPLAN, LA
- Very Easy
- Less than 15 mins
-
Pliers
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Was this helpful?
Thank you for voting!
stove gas burner would not light?
1 person
found this instruction helpful.
-
Robert from Hendersonville, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceram
... Read more
ic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.
Read less
Was this helpful?
Thank you for voting!
broken burner control knob
1 person
found this instruction helpful.
-
marcus from CARSON, CA
- Really Easy
- Less than 15 mins
pull old knob off install new knob
Was this helpful?
Thank you for voting!
backing for stovetop knobs
1 of 2 people
found this instruction helpful.
-
Norman from Tustin, CA
- Really Easy
- Less than 15 mins
the decorative backings on our stovetop knobs had become frayed, and I simply pried off the old ones,and installed the new ones. I have use Parts Select for years for various parts replacement, their service is quick and accurate. When I need a part, I always check here first.
Was this helpful?
Thank you for voting!
Control Knob Was Broke Due To Old Age
-
jayanti from w.bloomfield, MI
- Really Easy
- Less than 15 mins
Just replaced with the same color-almond
Was this helpful?
Thank you for voting!