My Orders
KGCR KitchenAid Cooktop - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
the knob was melted by a hot pan
21 of 25 people
found this instruction helpful.
-
David from Corinth, TX
- Really Easy
- Less than 15 mins
popped off the old knobs and put on the new ones in less than a minute
Was this helpful?
Thank you for voting!
There was a crack in the porcelain not letting it spark
23 of 36 people
found this instruction helpful.
-
Billy from Martinsville, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Was this helpful?
Thank you for voting!
broken ignitor insulation; repeated sparking after burner lit
15 of 21 people
found this instruction helpful.
-
Joe from San Bruno, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Was this helpful?
Thank you for voting!
Replaced Stove knob
9 of 13 people
found this instruction helpful.
-
Robert from Middletown, NJ
- Really Easy
- Less than 15 mins
Removed old one, installed new one
Was this helpful?
Thank you for voting!
igniter short circut
15 of 35 people
found this instruction helpful.
-
Jim from Grove City, OH
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replace igniters
Was this helpful?
Thank you for voting!
Spark Ignition Electrode was not sparking properly
5 of 10 people
found this instruction helpful.
-
Wade from Jacksons Gap, AL
- Easy
- Less than 15 mins
-
Pliers
Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the
... Read more
retainer clip.Works great.Thanks Wade
Read less
Was this helpful?
Thank you for voting!
Grate pads fell off- burner scratched surface-need special glue
4 of 7 people
found this instruction helpful.
-
Sandra from Lake Wylie, SC
- Really Easy
- Less than 15 mins
-
Screw drivers
Bought in auto repair store special black glue used for sealing gaskets. Husband needed to use latex gloves, toothpicks, ice pick, and small screw driver to glue and install new burner pads.
Was this helpful?
Thank you for voting!
Plastic anchor tips broken.
3 of 4 people
found this instruction helpful.
-
Thomas from COLORADO SPGS, CO
- Very Easy
- Less than 15 mins
Removed the broken items and replaced.
Was this helpful?
Thank you for voting!
Grommet broken
2 of 2 people
found this instruction helpful.
-
Ray from POST, TX
- Very Easy
- Less than 15 mins
Good
Was this helpful?
Thank you for voting!
Old knobs fell apart
2 of 2 people
found this instruction helpful.
-
Retta from FLOWER MOUND, TX
- Very Easy
- Less than 15 mins
Just put new knobs on. Perfect fit.
Other Parts Used:
Was this helpful?
Thank you for voting!
Knob skirt clips (2 of 4) broken
2 of 2 people
found this instruction helpful.
-
John from RAINIER, WA
- Really Easy
- Less than 15 mins
Gently pressed the lower two clips onto my thumbs as I pressed the skirt into the cooktop skirt hole. Be gentle or you can break the new skirt!
Was this helpful?
Thank you for voting!
2 control knobs were broken.
2 of 2 people
found this instruction helpful.
-
Sylvia from DELANO, CA
- Really Easy
- Less than 15 mins
I just replaced the broken knobs.
Was this helpful?
Thank you for voting!
igniter on top right front burner was shorting out,it would click but not ignite burner
2 of 3 people
found this instruction helpful.
-
Shelly J from KAPLAN, LA
- Very Easy
- Less than 15 mins
-
Pliers
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Was this helpful?
Thank you for voting!
Had melted knob on cooktop
2 of 3 people
found this instruction helpful.
-
Traci from Bozeman, MT
- Easy
- Less than 15 mins
Went great, part was perfect!
Was this helpful?
Thank you for voting!
the little tabs that hold the skirt in the hole break off
2 of 3 people
found this instruction helpful.
-
John from Sequim, WA
- Really Easy
- Less than 15 mins
I pulled the knobs off, lifted the broken skirts out and snapped the new ones in.
Was this helpful?
Thank you for voting!