KGCC506RWW07 KitchenAid Cooktop - Instructions

My husband and I replaced the igniter module, following directions we found online. We removed the old one, replaced it with the new one, and thankfully everything is working great!

I went online and discovered the repair method and schematic of the range. I removed the spark module after first removing the upper rear panel cover and replaced with the new part module ordered from your company and now the spark module operates all the gas elements when they are turned on thus lighting the gas burners. My mother in law ... Read more was thrilled, as she had been using matches and burning her finger tips,since the original range part malfunctioned. The only problem was the small screw from the original installation was not long enough , so it required some changes to get it affixed to the cabinet side.Thanks for the reasonable price and the right part for the job!!

Your website says these are the replacement rubber tips for the grates on the range. They arrive and they are too small and fall out. I spoke to the "chat" on your website. I am informed they do not sell the rubber tips separately. You have to purchase a new set of grates for $294. Ridiculous. Why sells rubber tips for grates that d ... Read more on't fit the existing grates. I wasted $24 in purchasing the grates which included $9.99 shipping and $5.40 shipping to return the item.

Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are ... Read more two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.

Removed back upper cover, unscrewed retaining screw from module. As noted in a comment from another do-it-yourselfer, I replaced screw with a longer one and reinstalled module. Note that the replacement part is not exactly the same as the old one(the wires are located differently), I noted the wire color codes with the slot number and r ... Read more einstalled them in the same slot number. Works fine.

We replaced the part. It was pretty quick and easy to install.

Replace igniters

pull old ones out of legs. need to glue new ones in, they fit too loose. Some kits contain glue. get some high temp head gasket cement. a drop on each one is plenty. I used some old porcelain glue and hope it will hold. the pads are 2 bucks each plus shipping so don't let them get away!!!

Removed the broken items and replaced.

Gently pressed the lower two clips onto my thumbs as I pressed the skirt into the cooktop skirt hole. Be gentle or you can break the new skirt!

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

Good

I pulled the knobs off, lifted the broken skirts out and snapped the new ones in.

the decorative backings on our stovetop knobs had become frayed, and I simply pried off the old ones,and installed the new ones. I have use Parts Select for years for various parts replacement, their service is quick and accurate. When I need a part, I always check here first.

1. Apply gas pipe joint sealer to treaded nipple on bottom of cooktop; 2. Install regulator on nipple with regulator direction arrow pointing to top of cooktop; 3. Tighten but do not overtighten as it may crack the aluminum body regulator; 4. Make sure the face of the regulator with the green painted surface faces the outside of the cabin ... Read more et; 5. Get a new gas flex hose to connect to gas pipe (got mine at Lowe's - 2 feet long with all the right fittings for about $15). 6. Follow instructions on gas flex hose - make sure you use gas pipe joint sealer only where indicated; 7. Turn gas shutoff valve back on and test for leaks using soapy water; 8. Turn on each cooktop burner to bleed out air.