KFIL KitchenAid Refrigerator - Instructions

Since it wasn't possible to squeeze the seal in between the door groove and the bar which closes the gap between the two doors, I cut the seal side in half and snaked it in from the top and the bottom. Since the cut is behind the bar when the door is closed there is no compromise in getting a good seal around the door. Note there was no ... Read more apparent way to easily remove this bar.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in ... Read more rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

I was hesitant to remove old seal, after I removed, I lined up new seal, and the seal popped into the slots very easily. Easy repair, no tools, worked great. The seal takes about 24 hour to seat itself for a great fit.

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was oft ... Read more en used to repair this issue. The service was great and the delivery was fast.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
... Read more />Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it wa ... Read more s the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped ... Read more up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??

Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.

Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues

Let the ice in the freezer melt while installing P trap drain tube

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.