KFDC500 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broiler pan missing
1 of 2 people
found this instruction helpful.
-
RAYMOND from JACKSONVILLE, FL
- Really Easy
- Less than 15 mins
ordered new broiler pan
Was this helpful?
Thank you for voting!
I wanted a second 8" canning element for home canning
5 of 15 people
found this instruction helpful.
-
Shelley from Powell, WY
- Really Easy
- Less than 15 mins
I purchased an 8" canning element for my new Kenmore Stove. The ordering process was easy. I printed my order out. I did not receive a confirmation by email, however I received the part in a timely manner. I was satisfied with the process.
Was this helpful?
Thank you for voting!
broken meat probe
0 of 1 people
found this instruction helpful.
-
Daniel from Massey, MD
- Really Easy
- Less than 15 mins
My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.
Was this helpful?
Thank you for voting!
The oven shipped without a temperature probe.
0 of 2 people
found this instruction helpful.
-
jerry from rochester, NY
- Really Easy
- Less than 15 mins
Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.
Was this helpful?
Thank you for voting!
Contractors on my home did not tighten nuts on terminal block when installing. This caused an arch across terminal burning up unit .
-
Robert from San Antonio, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm gla
... Read more
d I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.
Read less
Was this helpful?
Thank you for voting!
stove top got hot when using large pans
-
Albert from Bryant, SD
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the existing element and replaced it with the new one.
Was this helpful?
Thank you for voting!
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
-
Joseph from Channelview, TX
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
R&r
Was this helpful?
Thank you for voting!
Wiring Block shorted due to moisture and Stove had no Power
-
John from Roberts, MT
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-
... Read more
wire install and that did the trick.
Read less
Was this helpful?
Thank you for voting!
Terminal Block was melted where the cord had came lose.
-
Louise from Humansville, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this helpful?
Thank you for voting!
terminal block back of range shorted and burned
-
Louis from Grantsville, UT
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare
Was this helpful?
Thank you for voting!
Power block terminal failure
-
Leonard from Brazoria, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Ordered part needed. Much, much cheaper than purching a new range.
Was this helpful?
Thank you for voting!
terminal block cracked
-
James from Richmond, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Followed the easy instruction sheet provided.
Other Parts Used:
Was this helpful?
Thank you for voting!
Melted and fused together wires due to non-grounding of terminal block
-
Dr PauMari from Alamogordo, NM
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked
... Read more
together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.
Read less
Was this helpful?
Thank you for voting!