KFCS KitchenAid Refrigerator - Instructions

This gasket is just friction fit into a molded groove. Easy to pull out and replace.
When I googled looking for how to.. all sites described unscrewing a keeper. None described that this (and maybe others) simply has the push-in design.

I tested the ice maker first and got no response. So I bought the new ice maker and unplugged the connector in the back, loosened the 2 screws up top and took the bottom screw out. I took out the old one and then plugged the new one in and hung it back on the 2 loosened screws and put the bottom screw in and tightened the screws. I have t ... Read more o say it’s working great! Have plenty of ice again. Saved a lot of money by doing it myself. Buy your original model number part from Parts Select.

First turned off the water at the valve. Next I undid the 5 screws holding the plate that holds the pump. Next disconnected the power connectors, then the water lines. Next undid the screw holding the pump, removed pump. Next, mounted the new pump to the plate, this was tricky because it has to fit kind of upside down, so you have to ... Read more wrangle it into the proper position then align the screw hole. Next, secured it to the plate with the screw, re-connected the water lines, then the power. Before mounting it back to the fridge, I tested to see if it worked, well, it didn't. My heart sank. I re-checked all connections, I redid the entire process, disconnected and re-connected and still did not work. I researched the problem online and someone posted maybe the water filter might be clogged or defective. So I removed the water filter and put the stop plug in, and it worked perfectly. I went and exchanged the filter and plugged it in and still had the same problem. I am now suspecting the filter receptacle is the fault, but we will do without that for the time being. But the pressure is much better so changing the pump was still necessary. All in all a very interesting repair. I learned a lot about how the system works and now I need to replace the damper, it is very noisy.

As shown on the YouTube link sent with email receipt.
Removed back panel. Removed the clip securing the parts with long nose pliers. Unplugged the old, replugged the new. Replaced the clip to secure.

Unfortunately, the capacitor and relay did not fix the loud clicking issue.

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from ... Read more the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.

It is simple, unscrew the old screw in the new one.

Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy ... Read more to pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and ... Read more replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

So far haven’t done the repair and probably will give up. This issue is discussed in frequent questions area of your web site. Steve’s video needs to be updated to discuss what to do with end caps that are snapped, rather than screwed, in. Before decided to DIY, I looked at video. Video job is easy. Steve showed it was easy, but video end ... Read more cap has screws. I figured mine did too and so ordered the part. When placing order, rep. and/ or web site should point out issue as now that look at item on line can see no screw holes. As your instructions note for my issue, if can pry old unit off, challenge is to recall where everything that drops out goes when replacing. Because I’m stubborn, will probably try one more time, but likely will fail to swap out old for new end cap. Warning: screwless end cap replacement is not easy.

You need to remove both humidifier drawers plus the glass shelf for the bottom of the humidifier drawers and the bar at the front as a start. If I had known this before starting it would have sped up the install time. Then, pull out the deli drawer.

To remove the end cap (either side) there is a plastic tab to push down on ju ... Read more st over halfway back and then you can slide up the front of the end cap. Once you have slid up the front of the end cap a few inches, (past the channel it is locked into), you can pull it forward. You can observe the configuration on the spare part to see how this needs to be done.

To install the new end cap, reverse this process. The trickiest part is then re-inserting the deli drawer and the lid. Getting the lid onto the two axles was a bit of a struggle as the fit is very tight. Re-installing the humidifier parts is much easier. My repair time included using the opportunity to clean all of the removed drawers and shelves. If you know about the need to remove the humidifier drawers ahead of time and eliminate the cleaning I think this would take less than 15 minutes.

Remove the crisper baskets, Hinged lid, Glass shelves, support bars, and to make it easier - the door bins.
There are no screws on the end caps for this model of fridge, unlike some YouTube videos you might see.
There's a release catch nearly in the middle of the cap. With your index finger, press down on the tab, to release th ... Read more e catch, while lifting the front of the end cap. The end cap should lift up and away from the side wall of your fridge.
Be careful to then rotate the entire assembly - in the case of the right side end cap - towards you, so that you can disengage the tab on the crisper drawer temp controller, that fits in the back wall of the fridge.
Once you've unhooked the control rods to the crisper temp. control, you'll need to remove the crisper drawer runners.
Again - on this model, there are no screws. The runners just slide out from underneath their retaining plastic tabs. Slide them towards what would be the front of the fringe if they were in their natural position, they clear the retaining tabs and become free.
The control rods need to be re-attached on the new end cap.. just take your time click it between the various plastic tab.
Then insert the end tab of the crisper temp control in the back wall, rotate the entire assembly 90 degrees, so the end cap is aligned with the slide wall, and lower it into position until the retailing clip clicks into position. Congratulations, you've replaced your right side end cap!
Then reinstall all the supports, shelves, bins etc. and you're good to go.
Good Luck!

Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.

But this did not fix the problem. Will have to remove the door and inspect the insi ... Read more de of the door's lower hinge assembly.

The other instructions and the video provided by Parts Direct are pretty good with instructions, but they omit two steps. First, if you have an ice maker, you will need to unplug the connector on the back side of the panel you remove at the back of the refrigerator to access the drain tube. Just unplug it and you can move the removed pa ... Read more nel to the side without disconnecting any of the water lines. Second, the instructions say to just reconnect the "bottom end" of the new p-trap drain to the drain pan at the bottom of the refrigerator. They don't tell you there are two places to connect the new p-trap to the drain pan. The original tube/trough connected to the one at the back of the drain pan on the left (viewed from the rear of the refrigerator). At first, it looks like the new p-trap won't reach to it for the connection, but if you look closer, there is another connector to the right of the original one that the p-trap connects to properly. Replacing the drain trough with the new p-trap was actually pretty easy and would only take about a half hour. Add another half hour to give the refrigerator coils a good cleaning as they will need it now that you can reach them. The real time consumer, 3 to 4 hours, is needed to use a hair dryer to melt and clear the ice from the condenser at the back of the freezer so the water can drain. Just take your time and all the ice will eventually melt and drain out so the new p-trap will work properly.

pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh