KF560GDV Frigidaire Range - Instructions

Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.

the repair itself went smoothly. the clips that the new part connected to were old and slack. the clip came undone and had to pull the stove out to get to part from the back. i squeezed the clip together to make it stay on the new part and it held. the oven is heating well now.

Removed the old element by sliding the wires
attached to it. Unscrew 2 screws, slide the
new one to the wirings and put the 2 screws back.
It works. Praise the Lord.

I unplugged the stove and used a flashlight for light. I tried a phillips head, but it was too big. I then got a set of pliers and unscrewed the two screws an pulled out the element. I removed the 2 electrical plugs from the ends of the element and attached the new ones. They went on from the top where as the old ones slid from the si ... Read more de. after pushing the element back in i screwed the screws back in and the backings were a tad large so I bent them up and presto it was fixed!

pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as w ... Read more ell as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same

followed the video provided on line which was very helpful..

Removed element by loosening two screws, disconnected heater element and connected new element and reattached to oven wall. Turn on oven to check for heater to work. Confirmed heater worked. Repair complete.

I turned off the circuit breaker to the range. Next I removed the two screws that fastened the element to the rear of the oven. Then I pulled the element out far enough to be able to reach the spade clips and disconnected the element. I connected the replacement element to the clips and fastened it to the rear of the oven with the two scr ... Read more ews. I turned the circuit braker on and the element functioned properly.

Really easy process. First I unplugged the oven for safety then I proceeded to remove the 2 screws that were holding the old element in place. Next I removed the old element then installed the new one. After installing the two screws I connect the oven back to its power source and BANG!............. It works like a charm

I g ... Read more ive it a A+ installation

Oven is an in the wall unit. Normally it is an unplug and plug in. The old one had a melted connector, so the connector had to be cut off and replaced as well. Be sure to turn off the electricity at the braker to be safe, first.

If I didn't need my oven ASAP, I would not even have attempted to do this repair before my husband came home. But he wasn't going to be home for hours, and I needed it now!
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the o ... Read more ven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!

Thanks,
Vicki

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element

Removed the racks first. Then removed the two screws that held the element in place.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.