KESS907SSS06 KitchenAid Range - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

turn off breaker to stove. open oven door and locate two screws that are above the door that hold down the bottom of the front panel. the screws were not common headed but I had some odd ball screw driver heads that fit. the front panel had to be pulled out a little then lifted vertically to unhook it from the lip on the top of the sto ... Read more ve. after removing the knob there are two screws hidden under it that hold the control module too the panel. the light on the front panel can be sli to the side to release it from the panel so that you have more slack to unplug and change the wires from the old control module to the new. screw retaining screws back through front panel to new control module. slide light back onto lens in control panel. hang control panel back on stove and secure with the two screws above the front stove door. press new knob on. turn breakers back on

Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I ... Read more then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.

Getting at the part was difficult. The top and both side panels had to be removed to reach the blower. Once they were off, it was fairly easy to swap out the blower. The repair guy wanted $140 for the part and $160 to insall. I did it myself for $94! If you do it yourself, keep a good record of what screws came from where as you go. This ... Read more makes re-assembly much easier.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

Open oven dooor. With a philip screw driver remove the gasket plate at the bottom of the oven holding the seal gasket. pull seal gasket away from oven seal channel and clean surface before installing new seal. align seal pins to to seal channel holes be sure not to twist the seal insert pins in one at a time.Install lower bracket however ... Read more you may want to wet the fray ends of the seal gasket prior to screwing in plate to keep the ends from moving away from the bracket when scrwing it in place.

There were 4 screws to remove and 2 wires to disconnect. We placed the order on line for replacement. It arrived the next day. We simply installed the new element by connecting the 2 wires (very easy) and putting the 4 screws back in place. It works like new and was sooo easy.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

I removed the front control panel. The trick is that the 2 screws are only visible when you open the oven door. Make sure the power is turned off, wires and terminals are accessible. The cooktop has 2 latches in the back and 2 screw brackets in the front. When you remove the old cooktop, you will see how the cooktop connects to the st ... Read more ove top. Unscrew the 2 screws to the front brackets and remove the metal bar and black insulator. Slide the old cooktop off by pulling towards you or to the front of the range. Clean the electric elements, I vacuumed them. Slide the new cooktop in and ensure the 2 latches in the back slide into the stove top. Seat the cooktop and ensure the 2 bracket screw holes line up. Replace the metal bar and black insulator. Replace the 2 screws into the front brackets. Replace the front control panel and the 2 screws. Done!

slide into place

Our double-oven is wall-mounted, so accessing the backside to change the wires (as shown in the instruction video) was not a practical do-it-yourself option. After turning off the circuit breaker and disconnecting the broken broiler element, it is pretty easy to pull the four connection wires through the backside of the oven, which allow ... Read more ed us to disconnect the slide clips. We attached twist-ties to each clip/wire before disconnecting to keep the clips/wires from pulling back behind the oven wall when moving the new element into position. We found it necessary to crimp a few clips onto the new element to make secure connections, but the rest of the project went pretty much as shown in the video and the new element works great.

Removed back of oven. Disconnected 2 connectors on each side of element. Removed screws that were too rusted to use screwdriver with vise grips. Removed old element, inserted new element through holes in rear of oven.Installed 1 screw on each side of element in rear and 2 screws in front where brackets support the front of the element.Put ... Read more back panel back on. Push oven back in place, plug back in outlet.It works great and I didn't have to pay service man.

Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and conne ... Read more ctor back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install

The existing bake element was charred and in pieces so could not be pulled out. We destructively disassembled the range and pulled out the pieces along with the melted insulation. The wall behind was also scorched.

Removed oven door for easy access. Removed 4 phillip head screws that held broiler element from top of oven. pulled wires a couple of inches out from back of oven and used flat screw driver to help separate the wires connecting the broiler from the oven. Did the opposite to install the new element,.
The best part of this operation ... Read more was the fact that the part arrived from Part Select by Fed X the next day after ordering it all for a shipping cost of $8.75. Great Service Highly recommend Part Select.