KESC307H KitchenAid Range - Instructions

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

First , I turned off the circuit breaker to the oven.
Next, I removed the two screws at the front of the range top and slid the top out until I could disconnect the multi-plug connecting the wiring harness to the stove.
I then took the entire top out to a table and set it upside down. It was easy to unbolt and disconnect the le ... Read more ad to the element. One of the leads was burnt, so I had to replace it. I slid the new element into place, bolted it down in the same orientation as the old one and reconnected the leads.

I slid the entire top back into place on the range and re-installed the securing screws. Then I flipped on the circuit breaker and turned the element on.
Success! Perhaps I didn't really need to change the element since the burnt lead was the cause of failure. But its good to have a new part installed anyway.

A friend was kind enough to do the repair. It all went very easily... and the best part was that the replacement control panel was the cure. First thing was to turn off the circuit breaker to prevent any shocks. Then he just pulled the stove out.. removed the side screws... the screws under the control top... removed all 4 of the burne ... Read more r knobs and the nuts and washers holding them in place. The wires to the lights came off with a little wiggling... and went onto the new control top in the same order. Then everything went back into place... at which time we turned on the circuit breaker to find success. It was amazing to have it working again. Thank you for having these parts so that we were able to save a bundle of money on the repairs.

I think this does not qualify as a repair. I called and ordered the oven rack, it came in the mail and I put it in the oven. Nothing to it.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Simple. But beware changing just the bulb when the gasket is not secure.

I ran numerous tests to eliminate the on/off switch and to ensure the wires were not defective. Thus I came to the conclusion it must be the burner was defective. I ordered the part from parts.com. I received the part in less time than what was advertised. The part arrived in good condition. I placed the part in and it worked just li ... Read more ke new.

Thank You

Just as others said. Remove top holdown bolts with nut driver. Prop range top up.
Use a pair of plyers to remove wires (make sure you have a diagram to restore).
Use screwdriver to remove element hold down spring and wire holder. Replace element and replace wires and screws.

The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.

took the door off, removed the screws, removed the back of the door, took the broken glass out, put new glass in, reassemble door, put door back on.

Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.

looked on internet on how to remove top. an easy fix after watching video

Had to remove side panel then very easy

I have KitchenAid convection oven that is about ten years old . The hinge on the left hand side broke so I had to replace it. It took me about 2 hours to get the job done because I cleaned the door as I went . The change out while fairly strait forward did take some time . A lot longer the some of the people said .

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. ... Read more Thank you partselect and i would use them again in the future. billy