KERC607GBT1 KitchenAid Range - Instructions

Had to screw off old terminal block & screw on new one

That should have been an easy repair according to previous responders that replaced this part.

The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.

The second issue was I could not pull the connector through the hole where the sensor wires ... Read more pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.

NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.

Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!

After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)

The repair was simple:
PartSelect always seems to have the parts you need and they get them to you quickly.
Baking element - I removed the two screws that hold the element to the back of the oven ( Philips head). Disconnected the spade type electrical connections from each end of the element. Note: use some type of clamp to hol ... Read more d the wires from pulling back into the outer section of the oven. I used wooden clothespins). Reverse the process to install new element.
Broiler element - I placed the shipping container over the new baking element to protect it. Then removed the four screws holding the top element to the back of the oven ( Philips head). Take care to mark the 4 wires for the broiler element. ( 2 for outer coil & 2 for inner coil) Clamp these wires also after disconnecting. Slide the 2 "L" shaped hangers out of there slots. When installing the new element connect the wires first then slide the "L" shaped hangers back into the slots. reinstall the 4 screws and your done. I did the repair with out removing the oven door ( ours is difficult to get back on ) with the door off the job will take less time and access will be easier.

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the g ... Read more lass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!

Per the instructions listed in your customer replies

Had difficulty removing the two screws holding element(range is eighteen years old.Screws were badly rusted)After that,it was a piece of cake

Most of the basics have been covered in previous post. I can add this- those who claim 15 minute-fixes are delusional, unless they're appliance repairmen. Secondly- what will take time is the cleaning. If you have to do this repair, which requires extensive disassembly of the door, it would be foolish not to take advantage of the opportun ... Read more ity to thoroughly clean all four layers of glass. Take the glass panes outside and use oven cleaner. This takes time. Other than that, the pancakeing of the components on re-assembly is tricky, but you can do it. Don

It was difficult to reach the back of the oven inside to remove screws. I had to use an extended socket with a bit tip. When I tried to remove the element from the clips, the clips slid back inside the insulation at the back of the oven. I had to take the back panel off of the oven, push the clips through the opening and then I used ... Read more a bag clip to hold them so they would not slide back into the opening. I could not lift the door off-too heavy- to get closer to the back of the oven to put the clips and screws back on so I laid the oven on its back after putting the back cover on. The oven door was so heavy then that I had to prop the oven door open with my 24 inch rolling pin. I then leaned down into the oven and managed to get the clips and the screws back in. I then put the oven upright again, plugged it in, then had to re-level the whole thing. I turned it on and it worked. This probably would have been easier if I were not 65 years old and had some help. I was not giving up though. I got it done.

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws ins ... Read more ide oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover ... Read more and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

My wife was complaining about poor baking results with the oven in the home we just purchased, so I hooked up my digital temperature meter and found it was almost 50 degrees of, so I tried the ovens off set program to bring it closer into range. That did the trick ,but she complained about poor baking still. I watched the oven cycle about ... Read more 8 times and saw her problem. The oven was inconsistent when dropping below set temps, some times it was 20 degrees off, other times it was 80+ degrees off before the element kicked back on. I started with the sensor, it came with easy instructions including wire hi temperature wire nuts if the connectors didn't match... which they didn't. It was very easy to access the senor for replacement. Just unscrew about 10 screws, pull the back access panel off and there it is. Cut the connectors on both ends making sure to leave plenty of wire on each end. Wire nut them together and reinstall the back panel. Reset the oven off set back to zero and check the oven temp watching about 6 cycles. Comes right on now, and her first baking effort came out great...I am pretty sure that was the problem.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Followed Mfgs instructions.

ordered, came the next day and just slid it on the gas stem