KERC508LSS0 KitchenAid Range - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

took the back off stove to get to switch take pictures of where wires go as well as make a schematic this made it fairly simple no problems glad I did it

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold doo ... Read more r closed. Just spent $100 dollars and saved $1600 thanks guys.

Had to screw off old terminal block & screw on new one

I did the repair myself while my husband was at work. I lacked the brute strength to remove the door, so I ended up taking in apart while it was in place. Unfortunately, I only now noticed that instructions for installation were provided on your website. I did it without instruction, just making sure to note where screws had been re ... Read more moved so I'd be able to reassemble the works when I was finished. The worst part was loosening a couple of the innermost screws--even after a long soak in wd40, they were really hard to crack loose. Once I managed that, though, it went smoothly. Don't be intimidated; you can do this stuff yourself without calling--and paying--a repairman.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The secon ... Read more d one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip you ... Read more r breaker. But now we have a range with 4 burner after a year THANKS

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would r ... Read more equire me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started wi ... Read more th the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I ... Read more was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to ... Read more the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

One screw on each of the two cover plates removed, then element is pulled out enough to get at the connections. These are small blade connectors that slide off, two on each side, so 4 all together. The problem for me was that on one side the wires were to short and as soon as the blade connection was released the wire pulled back through ... Read more the hole and was difficult to retrieve because it was hiding in the insulation. If I were to do this again I would use a small zip tie around the wire before disconnecting it so I would have something to pull it back out with.

Took door apart no problem had a little trouble putting it back together just one piece I put back wrong had to start over not to bad still took less then one hour

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the g ... Read more lass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!