Home
KEDT105VAL0
Instructions

KEDT105VAL0 KitchenAid Range - Instructions

All Instructions for the KEDT105VAL0

Purchased home but stove had no broiler pan.

16 of 33 people found this instruction helpful.

Raymond from BLOOMINGTON, MN
Very Easy
Less than 15 mins

Purchased 2 piece broiler pan from this site

Was this helpful?

Inside glass window pane on oven door cracked.

7 of 7 people found this instruction helpful.

Susan from San Jose, CA
A Bit Difficult
30 - 60 mins
Screw drivers

First tried to replace the glass and gasket without removing the oven door. Removed all screws and took the door apart. However, I found it was very hard to get the gasket to stay in place and put the glass window in place with the door frame still attached to the oven and upright. Decided to go ahead and lift the door off the hinges b ... Read more

Read less

Other Parts Used:

Range Inner Door Glass

Glass Door Gasket

Was this helpful?

Broiler wouldn't heat

7 of 7 people found this instruction helpful.

Diane from Mill Valley, CA
Really Easy
15 - 30 mins
Screw drivers

First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

Was this helpful?

honeycomb filter in vent fell out..

8 of 10 people found this instruction helpful.

Larry from Brentwood, TN
Very Difficult
1- 2 hours

The honeycomb filter in the vent was missing so I bought the entire vent cap.. Thought it attach with 2 screws from inside the oven.. BUT -- when you loosen the screws, it wouldn't drop.. Looked at the new part and saw that it attaches to the vent outside the oven as well.. So to replace this puppy, you have to pull the cabinet apart.. ... Read more r />
Left it for another day.. Hopefully no grease fires..
Read less

Was this helpful?

Thank you for voting!

Broil Element Was Burned Out

9 of 14 people found this instruction helpful.

DAVID from COTTAGE GROVE, WI

Really Easy

15 - 30 mins

Nutdriver

1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element

Was this helpful?

Thank you for voting!

Oven would not reach selected temperature

6 of 6 people found this instruction helpful.

Howard from BRYAN, TX

Really Easy

30 - 60 mins

Screw drivers

First, shut off the power at the breaker panel. Next, I simply unscrewed the screws holding in each element, disconnected the leads, reconnected the leads to the new elements, positioned each element & reinserted the screws. A suggestion: Before loosening the screws, a light shot of PB Blaster or similar might help.

Other Parts Used:

Broil Element - 240V

Oven Bake Element 2600w 240v

Was this helpful?

Thank you for voting!

Oven bake element

6 of 6 people found this instruction helpful.

ross from DEARY, ID

Very Easy

Less than 15 mins

Screw drivers

Open oven door. Still power to the wall, but all Knobs in "OFF" position. two phillips screws, pull old element back, and disconnect both leads. Put the leads on the new element and reinsert with two mounting screws. Simple.

Was this helpful?

Thank you for voting!

The Bottom Element Was Not Heating

6 of 8 people found this instruction helpful.

y.d. from lagrange, KY

Really Easy

Less than 15 mins

Pliers, Screw drivers

Unplug first then took back off and took wire clips off and connectected the other on in worked fine you will like part select I just ordered apart for my frig. Waiting for it now.

Was this helpful?

Thank you for voting!

Oven wouldn't heat

5 of 5 people found this instruction helpful.

Michael from Wichita, KS

Really Easy

15 - 30 mins

Screw drivers

Ordered element and received it the next day. Removed two screws that holds element in place. I then pulled the element out about 3 or 4 inches and disconnected the two wires. Put new element in connected the wires mounted element in place with the two screws. Now works great!

Was this helpful?

Thank you for voting!

The upper broiler element had burnt and broken into.

6 of 8 people found this instruction helpful.

William from Manteno, IL

Really Easy

15 - 30 mins

Wrench (Adjustable)

I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.

Was this helpful?

Thank you for voting!

Oven wouldn't heat above 300 deg. F.

5 of 5 people found this instruction helpful.

Barry from WOODSTOCK, GA

Difficult

1- 2 hours

Nutdriver, Pliers, Screw drivers

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 ... Read more minutes) after that.
Read less

Was this helpful?

Thank you for voting!

light bulb in water ice freezer door went bad

8 of 14 people found this instruction helpful.

Carl from RIVERSIDE, CA

Very Difficult

More than 2 hours

Screw drivers

I didn't. Don't know how to get to light bulb to change it for this specific model

Was this helpful?

Thank you for voting!

Loose terminal caused block to overheat and break

6 of 10 people found this instruction helpful.

Dana from Black Mountain, NC

Really Easy

Less than 15 mins

Nutdriver, Screw drivers

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Was this helpful?

Thank you for voting!

did not heat properly

5 of 7 people found this instruction helpful.

Ronald from Powhatan, VA

Really Easy

Less than 15 mins

Screw drivers

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, Removed the old element and installed the new one

Was this helpful?

Thank you for voting!

bottom heating element was bad

4 of 4 people found this instruction helpful.

glenn from greenwood, DE

Easy

Less than 15 mins

Screw drivers

Two screws held the element in place, removed the screws and pulled the piece out.
Back of piece has two wires attached, unplug them then attach the new element and replace the two screws to remount.
First make sure the breaker to the range is turned off before starting the repair.

Was this helpful?

Thank you for voting!

All Instructions for the KEDT105VAL0

16 - 30 of 312
Prev
1
2
3
4
5
...
21
Next