Home
KEDS2
Instructions

KEDS2 KitchenAid Range - Instructions

All Instructions for the KEDS2

The inner most glass cracked

8 of 9 people found this instruction helpful.

Debra from Ocala, FL
A Bit Difficult
30 - 60 mins
Screw drivers, Socket set

1. Open door and place a nail in the small circle in each of the two side hinges. This step is crucial. It keeps the hinges from springing back into the oven when the door is removed.

2. Remove the 2 screws on the oven door at the top of each spring. Close the door until stopped by the 2 nails, then lift the door up and off the ... Read more

Read less

Was this helpful?

Inside glass window pane on oven door cracked.

7 of 7 people found this instruction helpful.

Susan from San Jose, CA
A Bit Difficult
30 - 60 mins
Screw drivers

First tried to replace the glass and gasket without removing the oven door. Removed all screws and took the door apart. However, I found it was very hard to get the gasket to stay in place and put the glass window in place with the door frame still attached to the oven and upright. Decided to go ahead and lift the door off the hinges b ... Read more

Read less

Other Parts Used:

Range Inner Door Glass

Glass Door Gasket

Was this helpful?

honeycomb filter in vent fell out..

8 of 10 people found this instruction helpful.

Larry from Brentwood, TN
Very Difficult
1- 2 hours

The honeycomb filter in the vent was missing so I bought the entire vent cap.. Thought it attach with 2 screws from inside the oven.. BUT -- when you loosen the screws, it wouldn't drop.. Looked at the new part and saw that it attaches to the vent outside the oven as well.. So to replace this puppy, you have to pull the cabinet apart.. ... Read more r />
Left it for another day.. Hopefully no grease fires..
Read less

Was this helpful?

Thank you for voting!

Broiler wouldn't heat

7 of 7 people found this instruction helpful.

Diane from Mill Valley, CA

Really Easy

15 - 30 mins

Screw drivers

First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

Was this helpful?

Thank you for voting!

Broil Element Was Burned Out

9 of 14 people found this instruction helpful.

DAVID from COTTAGE GROVE, WI

Really Easy

15 - 30 mins

Nutdriver

1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element

Was this helpful?

Thank you for voting!

Electric burners where consistently intermittently working right. Sometimes they would work on High but not able to adjust to low heat. Sometimes they would just not want to come on at all. Occasionally there was a spark at the connection. If I jiggled the element just right it may or may not wo

7 of 9 people found this instruction helpful.

JOAN from Pickford, MI

Easy

15 - 30 mins

Screw drivers

Thought we was going to have to replace the range all together, due to most parts not being available for this model anymore. Since this is an expensive model, we did not look forward to having to replace it. So I thought just by chance I would check to see if anyone had parts to help in repairing it. Part Select did happen to have the ... Read more Surface Plug-in block kit that was needed. After going at least a year with this problem, I am sooooo happy to say it is finally fixed and working great! Thanks much Parts Select.
Read less

Was this helpful?

Thank you for voting!

Oven bake element

6 of 6 people found this instruction helpful.

ross from DEARY, ID

Very Easy

Less than 15 mins

Screw drivers

Open oven door. Still power to the wall, but all Knobs in "OFF" position. two phillips screws, pull old element back, and disconnect both leads. Put the leads on the new element and reinsert with two mounting screws. Simple.

Was this helpful?

Thank you for voting!

Oven would not reach selected temperature

6 of 6 people found this instruction helpful.

Howard from BRYAN, TX

Really Easy

30 - 60 mins

Screw drivers

First, shut off the power at the breaker panel. Next, I simply unscrewed the screws holding in each element, disconnected the leads, reconnected the leads to the new elements, positioned each element & reinserted the screws. A suggestion: Before loosening the screws, a light shot of PB Blaster or similar might help.

Other Parts Used:

Broil Element - 240V

Oven Bake Element 2600w 240v

Was this helpful?

Thank you for voting!

needed new drip pans

7 of 10 people found this instruction helpful.

Janice from Kerrville, TX

Really Easy

Less than 15 mins

New ones fit perfectly, and looks beautiful!

Was this helpful?

Thank you for voting!

Oven Light Would Not Work, Old Bulb Broken

9 of 16 people found this instruction helpful.

LOUIS from FREEPORT, TX

Really Easy

Less than 15 mins

Nutdriver, Screw drivers

Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.

Other Parts Used:

Light Bulb - 40W

Range Light Gasket

SOCKT-LITE

Was this helpful?

Thank you for voting!

Sparking Burner

6 of 8 people found this instruction helpful.

Patti from Burbana, IL

Really Easy

Less than 15 mins

Pliers, Screw drivers

Followed instructions from previous repair story!!
Pulled old burner out. Unscrewed plug element. Cut old wires back about 6 inches from plug. Attached new part with wire nuts provided and covered with shrink sleeves provided. Attached plug with provided screw and slipped in new element. Works great!!
I want to thank the pr ... Read more evious posters for posting their detailed repair stories....without reading those, I may have called a repair service and paid big bucks. Thanks to all previous posters for the detailed information they provided!! PS...The parts arrived in amazingly quick!!
Read less

Other Parts Used:

Surface Burner - 8 Inch - 2600W

Range Surface Burner Plug-In Block Kit

Was this helpful?

Thank you for voting!

The Bottom Element Was Not Heating

6 of 8 people found this instruction helpful.

y.d. from lagrange, KY

Really Easy

Less than 15 mins

Pliers, Screw drivers

Unplug first then took back off and took wire clips off and connectected the other on in worked fine you will like part select I just ordered apart for my frig. Waiting for it now.

Was this helpful?

Thank you for voting!

Oven wouldn't heat

5 of 5 people found this instruction helpful.

Michael from Wichita, KS

Really Easy

15 - 30 mins

Screw drivers

Ordered element and received it the next day. Removed two screws that holds element in place. I then pulled the element out about 3 or 4 inches and disconnected the two wires. Put new element in connected the wires mounted element in place with the two screws. Now works great!

Was this helpful?

Thank you for voting!

The upper broiler element had burnt and broken into.

6 of 8 people found this instruction helpful.

William from Manteno, IL

Really Easy

15 - 30 mins

Wrench (Adjustable)

I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.

Was this helpful?

Thank you for voting!

Electric burner on stove would not work

5 of 5 people found this instruction helpful.

Ronald from Fresno, CA

Easy

30 - 60 mins

Screw drivers

The first thing I did was to turn the power off to the stove by turning the Stove circuit breaker off at the Main breaker panel. I next removed the 4 burners by pulling them out of their plug-in blocks. I then removed the four screws that held the top of the stove to the body so I could access the bad plug-in block, the screws were loca ... Read more ted under each of the burners drip pans. I next removed the screw holding the bad block. I lifted up the top of the stove so as to relocate the bad block, with wires connected, through the opening of the back burner. The bad block was located in the front rt part of the stove and by rerouting this to the back I could lay the top down and have easy access to what I needed to replace. I next used the knife to make a cut down the length of the old shrink tubing so as to gain access to the old splice. I next removed the old wire nuts which allowed the removal of the bad block. I then install the new clips into the new block. I installed one each shrink tubing onto each of the pigtails from the new clips and twisted the one new wire to the stove wiring harnes were the old wire was connected . I connected the seconded wire in the same manner. I pulled on each wire to verify that they were tightly secured together. I then positioned each shrink tubing over each wire nut (you have to fold the wire nut and wires down against the wire so as the shrink tubing will slip over the wire nut) and used a heating tool (hair dryer on high) to shrink the tubing around the wire nutted connection. I next installed the metal clip that would hold the block to the stove top. I placed the new block back to the location where the old block came from and secured it with the new screw provided by the kit. I re-installed the four screws to hold the top down, plugged in the four burners, turned the power on at the breaker box and turned the burner on to test that it work.
Read less

Was this helpful?

Thank you for voting!

All Instructions for the KEDS2

31 - 45 of 472
Prev
1
2
3
4
5
...
32
Next