KEDS1 KitchenAid Range - Instructions

unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

Pulled out element, plugged in new element. About 5 seconds.

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into ... Read more the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires fom the old element .. connected them to the new element ... put the screws back ...and tested. problem solved

Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connec ... Read more ted them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.

came only I had to order the set again

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), ... Read more which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. ... Read more Thank you partselect and i would use them again in the future. billy

I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as supp ... Read more ort to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of bur ... Read more ner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed

My son ordered the part, which came very fast,
It was a perfect fit, and the job went very smooth. I have no story to tell except that Mom was happy to have the oven again and a VERY helpful son!!!!