KEBS246 KitchenAid Wall Oven - Instructions

Screwed in light bulb and glass protector

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

FIRST: I Shut off the circuit breaker to the oven. Then: 1. Removed convection-fan cover (it was partially blocking the bake-element screws). 2. Unscrewed 2 bake-element screws. 3. Pulled old bake element forward to expose connectors. 4. Disconnected both connectors and discarded the old element. 5.Connected the new element and pushed i ... Read more t in so that plate was flush against the back of the oven. 6. Re-installed the 2 element screws. 7. Re-installed convection-fan cover. LASTLY: Turned on the circuit breaker to the oven and baked a cake! IMPORTANT: The original screws can be very, very tight. When removing them, be sure to use a socket wrench or other tool that gets a firm grip on the hex heads, or you could round the corners of the heads, permanently damaging the screws.

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to ... Read more the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The secon ... Read more d one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Took off the oven door, oven in wall mount, had to pull oven 80% out to access both end of spring holders, reattached springs, slide oven back into place, installed face-plate and oven door. The most difficult part was pulling oven out of wall, I did not know it would be that heavy.

Had to screw off old terminal block & screw on new one

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

We turned off the power to the oven and removed the oven racks. Then we used a screwdriver to remove the metal plate in the back of the oven which held the connection for the old heating element. The element pulled out easily and then we connected the wires to the new element. Very simple.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.