Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Purchased home but stove had no broiler pan.
16 of 33 peoplefound this instruction helpful.
Raymond from BLOOMINGTON, MN
Very Easy
Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
Inside glass window pane on oven door cracked.
7 of 7 peoplefound this instruction helpful.
Susan from San Jose, CA
A Bit Difficult
30 - 60 mins
Screw drivers
First tried to replace the glass and gasket without removing the oven door. Removed all screws and took the door apart. However, I found it was very hard to get the gasket to stay in place and put the glass window in place with the door frame still attached to the oven and upright. Decided to go ahead and lift the door off the hinges b
... Read morey removing the two final screws. Then the door could be layed flat on the floor and it was much easier to put in the insulation and glass pane.
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
7 of 7 peoplefound this instruction helpful.
Jared from UNION GROVE, AL
Really Easy
30 - 60 mins
Pliers, Screw drivers, Socket set
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the
... Read more wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Read less
Was this helpful?
Thank you for voting!
honeycomb filter in vent fell out..
8 of 10 peoplefound this instruction helpful.
Larry from Brentwood, TN
Very Difficult
1- 2 hours
The honeycomb filter in the vent was missing so I bought the entire vent cap.. Thought it attach with 2 screws from inside the oven.. BUT -- when you loosen the screws, it wouldn't drop.. Looked at the new part and saw that it attaches to the vent outside the oven as well.. So to replace this puppy, you have to pull the cabinet apart..
... Read morer /> Left it for another day.. Hopefully no grease fires..
Read less
Was this helpful?
Thank you for voting!
Temp Sensor not working - Oven Overheating
6 of 6 peoplefound this instruction helpful.
Lee from FORT WORTH, TX
Really Easy
30 - 60 mins
If doing this for the first time, it's harder to replace than described by others.
Start by removing the oven door. Reach in to unscrew the two screws that hold the sensor in place on the back wall of the oven. I was working on the upper oven of a double wall oven and found it more comfortable to sit on a tall bar stool whil
... Read moree working. Pull the sensor partially out and you will see the connector wire running through the sensor opening. The sensor connector plug is too deep into the oven to reach with fingers or any tool. Next unscrew the 6" round heat circulator fan just below the sensor on the back wall of the oven. Pull the fan partially out and you will see the plug for the temp sensor directly behind. You may have to push some of the insulation of out of way. Unplug the old sensor and pull it back out directly through the sensor opening. Take the new sensor and thread it in through the opening and plug it in. Reinstall the circulator fan and then screw the new sensor in place. This should complete the temp sensor replacement.
Read less
Was this helpful?
Thank you for voting!
Stove top wouldn't come on. Oven couldn't go higher than low heat
7 of 9 peoplefound this instruction helpful.
Peter from FREDERICK, MD
Really Easy
Less than 15 mins
Screw drivers, Socket set
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00 Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer
... Read moreed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine. Thank you, Thank you Part Select for your help and honesty.
Sincerely Peter from Maryland
Read less
Was this helpful?
Thank you for voting!
Oven Light Would Not Work, Old Bulb Broken
9 of 16 peoplefound this instruction helpful.
LOUIS from FREEPORT, TX
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.
I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15
... Read moreminutes) after that.
Read less
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 peoplefound this instruction helpful.
Carl from RIVERSIDE, CA
Very Difficult
More than 2 hours
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Bake element failed and Cohen's Elec. Repairman could not work me back into schedule until after my holiday gathering had occurred.
12 of 27 peoplefound this instruction helpful.
CATHERINE from PIKE ROAD, AL
Really Easy
15 - 30 mins
Pliers, Screw drivers
Since I had to pay an $80 house call fee, I asked repairman to tell me the model number for the element, called Parts Select, ordered the element myself and saved my weekend of 17 hungry guests. So, I guess you would say I paid $80 for a diagnosis; I think I really knew the problem and solution all along as I have ordered to-install
... Read morestove top element before.
Read less
Was this helpful?
Thank you for voting!
Loose terminal caused block to overheat and break
6 of 10 peoplefound this instruction helpful.
Dana from Black Mountain, NC
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this helpful?
Thank you for voting!
Inner door glass cracked in 3 places
4 of 5 peoplefound this instruction helpful.
John from Emmetsburg, IA
Easy
15 - 30 mins
Nutdriver, Screw drivers
Removed 3 screws on bottom edge of door,2 screws on top edge of door. Outside of door comes off. Then use a 1/4 nut driver and remove glass window supports until you get to the inner door glass. Reverse to assemble. Gasket was okey.
Was this helpful?
Thank you for voting!
DO NOT USE THIS COMPANY!!!!!
4 of 5 peoplefound this instruction helpful.
Jeff from ARGYLE, TX
Really Easy
30 - 60 mins
The part showed up with no markings on it saying it was glass or fragile or anything. So naturally, the UPS or whoever people broke the glass in transit. Have been trying to get it replaced/returned for almost a month now.
Customer service is a joke and when you call the 800 number it always says "no reps are available"<
... Read morebr /> AVOID using PARTSELECT at ALL COSTS
Read less
Was this helpful?
Thank you for voting!
Broken glass on inside of oven door
4 of 5 peoplefound this instruction helpful.
Peggy from Bronson, MI
Easy
30 - 60 mins
Nutdriver, Screw drivers
Take the time to pull off the door from the hinge; which is to simply pull it up to release with the door open approx. 4 inches. Have a Philips head screwdriver and a nut driver set available. Keep the screws grouped and the take it apart in the logical sequence. It took about 30 minutes total to complete the job. But then again, it w
... Read moreas a woman who did it!
Read less
Was this helpful?
Thank you for voting!
Cracked oven glass
3 of 3 peoplefound this instruction helpful.
Kenneth from St. Augustine, FL
Easy
30 - 60 mins
Nutdriver, Pliers
Lots of screws but if you have the proper sized nut driver it goes quite easily. Take time to see how the inner glass is mounted to the oven door. There are also screws on the bottom of the door that you need to remove to get the inner panel off. The door itself can stay on the hinges
My Orders
