KEBK2 KitchenAid Wall Oven - Instructions

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. ... Read more Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

This is a microwave/ Oven slide in unit. You DO NOT need to slide out the unit, the repair can be done from inside the oven. Just be careful on pulling the wires from the unit so they do not break. I used shrink wrap over the joints but you can use tape as long as it can take the temperatures

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

Had to screw off old terminal block & screw on new one

Took off the covers and replaced the little bulbs. Took a long time to figure out how to get the covers off. Bulbs were $26 apiece!

I ordered the oven door gasket on Dec 20th and it arrived before Christmas. The installation was very easy and now we have a good seal on the door. Thank you for the rapid response and timely delivery.

Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.

Removed one trim piece on top of inner door with philips screw driver(4 screws). Claened all remaining glass from door. Placed rubber gasket from old glass to new glass along top. Laid new glass in place - reinstalled trim piece - reset door on oven.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Unpacked the glass. Removed four Phillips-head screws. Slid new glass in. Replaced the four screws, and job was done!

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago ... Read more ??

The Kitchenaid oven has 2 interior oven lights. They are behind rectangular glass panels, in an assembly housing The repair is pretty simple. Shut off the power at the breaker box to the oven first. First remove the small screw that holds in the assembly with a Phillips screwdriver. Put down a white piece of paper towel to catch it ... Read more in case it drops. It is grey color and hard to find against the bottom of the oven. This will free up the assembly and you can move it out. There is a wire on the back so it only comes out a short distance. Next the glass panel covering the bulb must be removed. The small metal clamp with 2 projections that act like a spring to put tension on the glass. Gently pull this out parallel to to the glass and it will release the lens. The old bulb is a simple 2 prong halogen that pulls out easily. Replace it with the new bulb carefully pushing the prongs in. If you did not turn off the power the light will come on immediately. it will get hot quickly so don't touch it for more than a few seconds. Next slide the glass lens back into place into the back of the assembly. Slip the other clip with the screw back on the front. Replace the assembly back into the oven side opening. Secure by replacing the small screw removed in the beginning. You are done. It is about a 5 minute job start to finish. I would replace both bulbs even if only one went out because the other one probably will go out a short time later and you will have to go through this again soon. Oh, and cheap bulbs are not worth it. They are very dim and burn out quickly. Go with the better bulbs you get from PartSelect.

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.