KEBC247KSS06 KitchenAid Wall Oven - Instructions

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a ... Read more lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.

This is a microwave/ Oven slide in unit. You DO NOT need to slide out the unit, the repair can be done from inside the oven. Just be careful on pulling the wires from the unit so they do not break. I used shrink wrap over the joints but you can use tape as long as it can take the temperatures

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.

Simple - Removed oven door attached retainer with screw.Re attached door.

Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.

Your prices are great "Parts Select".

Jan

Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

Had to screw off old terminal block & screw on new one

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long beca ... Read more use the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

Took the door off, removed the screws, took door cover off, cleaned the other two pieces of glass and the new one, and then reassembled. I set the screws aside so I put them back in the same holes. I never want to take the chance of a possible cross threaded screw not going back into the same hole. ... Read more Note:Now is a good time to clean edges with oven cleaner before reassembly.

A generic video on Youtube was actually very helpful as it showed how to remove the door from the oven for easier glass replacement. The only tricky part is getting the panes of glass in the correct order during reassembly,as there are actually 4 pieces in the door. Only the piece that faces the oven's interior was cracked on mine. The tw ... Read more o inner pieces between the two outermost pieces are the ones not to mix up. This little repair also gave me the opportunity to thoroughly clean all 4 pieces of glass that had become rather dirty over 12 years. Now the oven door looks like new!

I followed the instructions for installation on your site. I encountered two problems. I was unable to unscrew several screws. I had to used wd40 and slight encouragement from a soft hammer. Also, I was glad for the advice in one instruction about paying attention to the type of screw (flat or more flat). Otherwise, when ... Read more I was ready to put everything back together, I would have had some problems. The flatter screws definitely had to be used in certain areas.

Took off the covers and replaced the little bulbs. Took a long time to figure out how to get the covers off. Bulbs were $26 apiece!