KDRP407HSS13 KitchenAid Range - Instructions

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

I am not the handiest guy around so i was a little nervous doing this job but figured i would take a crack at it ( no pun intended). Took the door off as per instructions from kitchenaid , unscrewed all the outer screws , took off the back of door unscrewed the metal bar holding the glass in ( there are 3 levels of glass) took the 2 good ... Read more glass sheets out got to the broken glass removed that put the new one in , replaced all the other glass and screws and put door back on, and i felt so proud. Probably saved about 150 dollars by doing it myself. I feel so proud.

I found some of the feedback posted on this site very helpful. Taking photos as I went along was also very helpful in remembering how to put it back together. There are several over-lapping pieces to the door and you have to be careful to put things back together in the correct order. Lining up the screw holes on the hinges with the do ... Read more or is also a little tricky.

It was a matter of swapping out the old door with new door. In all, it was a snap . Around 10 screws to take it apart and a few brackets to hold it all together.

cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner

Removed and replaced boiler element

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem

This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes ... Read more of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.

Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.

I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me ... Read more to pull the connection apart.

All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.

Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.

XLarge pizza tray in a 450 degree oven - slam the door & CRACK. Replacement glass arrived on Saturday - VERY FAST DELIVERY. Placed 2 allen wrenches in both hinges - open the door half way & lift up. Place the door on a towel. Removed 6 screws, lift & seperated the inner oven covering, removed the broken glass & cleaned inside & replaced w ... Read more ith new glass. More time was spent cleaning & coming up with a tool to fit into the hinge

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

Quickly

I pinpointed the location of the sound, took off the protective plate, felt it vibrating against the plate. I disconnected the power supply, and looked at the wirings and how it was connected, saw some burning residue surrounding the area of the Transformer. Then figured that I could simply replace this. I wrote down the Model and Seri ... Read more al number of the Stove, searched online, found this site. Located the part on the diagram, then simply ordered it. My part arrived in 3 days, and had the part replaced the next day. Couldn't be a smoother fix. Thanks.

removed double wall oven light lens install bulb replace lens fini