KDFE454CSS0 KitchenAid Dishwasher - Instructions

After shutting off electricity, lay dishwasher on it's side (use a towel to absorb any water) then just use nut driver to remove faulty valve.

1. Disconnect power at the breaker, 2. remove two wood screws fastening the dishwasher to the cabinet and slide the unit out approximately 2 inches. 3. Remove old latch strike and replace with redesigned strike. 4. Slide unit in and reattached to cabinet. 5. Remove 11 screws holding inner panel of door assembly and one screw holding ... Read more user interface unit to door. 6. Disconnect snap cable to latch assembly and replace the latch unit. 7. Reassemble.

Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.

Unplug the dishwasher,take the screws out of the coutertop,then slide dishwasher out turn it on its side. Then take a torx screwdriver and remove 2 mounting screws. Unplug the wires going into the motor and replace the motor with the new one. But you need to replace the grommet the motor shaft slides up into or it will still leak.

Simply snap the old one off and snap the new one on. Simple as that less than 15 seconds.

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

I purchased this misguided by the official response to "Doug" on April 17, 2018, which at the time was labeled as "most helpful". This is NOT the little grommet in the center. This is a big grommet that goes no the supply pump. This is #14 in the diagram. (#15 is actually the clamp that holds it). If you are looking for the little grommet ... Read more that goes on that stem on the central recirculation pump, that part is not available, it only comes fused on the sump, and for replacing the sump you have to disassemble the whole bottom part of the dishwasher, pumps, sensors, valves, hose...even this big grommet. A lot of work, and since you are at it, you might want to replace both grommets. If you need THIS big grommet (#14) only, then it is not so much work, just take out one clamp, one connected cable, and the grommet to replace. But check if your machine has reusable clamps, because if not, you might want to order a new clamp. Good luck!

Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done

Per the you tube video

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Removed old parts by breaking them with a screwdriver. Insert thr stainless slide. As shown by twisting thought through wire rack the rest is easy.

Removed old gasket, cleaned track and replaced gasket-also quit using Cascade pellets and went back to using Cascade powder with a numerical "rating" of 6. The pellets of even 10 caused the washer to leak, obviously too much foam would not float the float to actuate the pump.

It was very easy to pry off the old wheel assemblies with a screwdriver and pop the new ones in place. Although the part is called "wheel" it is actually the plastic piece containing two wheels. I thought it was a little confusing to just call it "wheel" as each piece has two wheels. It was an easy repair.

Removed and trashed unnecessary extra "stuff" originally provided in top rack by KitchenAid. Followed installation instructions contained with parts. Pictures were poor but usable after studying them. Thanks to whoever developed the replacement instructions - would have been near-impossible without them. Customer service was efficient ... Read more , polite, helpful, accurate and more than I could have asked. Thank you all

The left side took 20 minutes the right side took 3 minutes. The instructions do not describe how to remove the old assembly but rather just assume you have already done it. It takes one minute to see how the six parts fit together and then you just have to begin disassembling the easiest piece. The final cover removal required a flat hea ... Read more d to pry apart two pieces held together in a pressure fit with round tabs locking them in. I was worried about breaking a piece in case the new parts didn't fit properly and I would have to reinstall the old pieces temporarily but you just have to keep the faith and open it up for final removal. Installing the new parts was simple however it would be nice if the images on the instructions were of better quality. The result was perfect and the kit feels more robust than the original parts. There is nothing here an average person can't do with a screwdriver and a little patience.