KDFE3 Dishwasher - Instructions

Easy...easy....I first watched YouTube videos on how to fix our problem. We replaced both tracks and also the rack adjuster on both sides of the rack. The entire repair took about an hour and most of that time was spent finding the tools at our house!! I ordered the parts on a Sunday evening and they were at our house on Tuesday!!! ... Read more Will use this sight again if repairs are needed.

I purchased this misguided by the official response to "Doug" on April 17, 2018, which at the time was labeled as "most helpful". This is NOT the little grommet in the center. This is a big grommet that goes no the supply pump. This is #14 in the diagram. (#15 is actually the clamp that holds it). If you are looking for the little grommet ... Read more that goes on that stem on the central recirculation pump, that part is not available, it only comes fused on the sump, and for replacing the sump you have to disassemble the whole bottom part of the dishwasher, pumps, sensors, valves, hose...even this big grommet. A lot of work, and since you are at it, you might want to replace both grommets. If you need THIS big grommet (#14) only, then it is not so much work, just take out one clamp, one connected cable, and the grommet to replace. But check if your machine has reusable clamps, because if not, you might want to order a new clamp. Good luck!

Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Removed old gasket, cleaned track and replaced gasket-also quit using Cascade pellets and went back to using Cascade powder with a numerical "rating" of 6. The pellets of even 10 caused the washer to leak, obviously too much foam would not float the float to actuate the pump.

I pulled the rack and removed failed parts, then reassembled. I would note that the videos are helpful as dishwasher racks can be a bit of a puzzle.

Why manufacturers use so much plastic in a heated environment is beyond me. The heat cycle degrades the plastic to failure - poor design!

Super simple.
Remove all screws around the stainless metal shroud inside the door. DONT remove the hinge screws.
Torx bit required.

Unplug detergent dispenser and place outer door assembly aside. Dispenser has small clips holding it in, top, bottom and sides I believe. Push these in, dispenser falls out into dishwashe ... Read more r.

Insert new unit, reverse all steps. Done.
Dont for get to reattach the wires!

Followed a video, pretty straightforward. Be sure to clean all the area. My husband used cotton swabs to clean all the gunk.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

I replaced both upper rack tracks because the spot welds on one of the factory tracks failed after 18 months. The welds just rusted away and let go. The other track appeared to be close to failure so I replaced both of them. This repair is actually quite easy, but in order to change the tracks, you must pull the appliance out at least a l ... Read more ittle more than halfway in order to reach the screws that hold the tracks in place. There are four such screws on each side -- they are fastened through the exterior face of the tub. Here is the process:
Use a 1/4" nut driver to remove the bottom front (kick) plate from the appliance. There are two screws, one at each end. There should also be two screws fastening the dishwasher to the countertop. You'll need to open the dishwasher door to see these and remove them. At the bottom of the dishwasher again, you might need to screw the front (2) leveling feet in to lower the dishwasher and provide clearance. Once done, just (gently, slowly) pull the appliance out of the cabinet. Check to make sure your power wiring, drain hose, and water supply hose are all long enough to do this. If necessary, disconnect any of these that are too short. if your power wiring is short, as mine was, you'll need to disconnect the circuit breaker, then remove the junction box at the lower front right side of the dishwasher, then disconnect the power and ground wires.
Once out of the cabinet, use a 5/16" nut driver to remove the four screws holding each rack slide in place and remove the track. The rubber mounts will come out with the track (new tracks include new rubber mounts). Clean any residue from the track mounting area inside the tub before installing the new track. This whole replacement process should take a total of 3-4 minutes per side.
To finish up, just reverse the process. When sliding the dishwasher back into place, make sure the fiberglass insulation stays in place completely around the outside of the tub.
Because the tile on my kitchen floor does not continue under the dishwasher (tile was installed after the cabinets), it was absolutely necessary to turn in the leveling feet to get the appliance out. Since this also makes it very difficult to get a wrench around the plastic feet, I used a very small socket (3/16"?) on the top of the leveling feet stems. This makes it really easy to turn the feet.
I the appliance designers had engineered things better by fastening the tracks from inside the tub, this would be a 5-minute job. But it's still not bad at all.

Ordered the "right" part according to the diagram. The part I received was about 1/4" too long so I couldn't use the whole manifold. Took the rubber end off and - fortunately- it fit the old manifold. Dishwasher works fine now. Wish I could have ordered just the rubber valves.

The valve has a plastic fitting to attach the the water line with a hose fitting. Was not carful enough with the original and damaged it attaching the water line. Ordered a replacement fitting. While it is possible to replace the water inlet valve without pulling the dishwasher out from the cabinet found it was easier to get at with the m ... Read more achine out. The video does and good job of showing the removal and replacing the valve. Easy job, don't be like me and be careful attaching the water line.

My husband called Part Select and described the problem. After we sent a couple of photos to the technician, she determined the part that we needed...a top rack assembly unit...and it arrived within a few days.
I watched the video that Part Select provided and it made the job so much easier than if the new part had been sent with a b ... Read more ooklet of diagrams and written instructions. The video showed exactly how to dismantle the old part and then install the new part. It was also helpful to compare the part I was working with to the same part on the other side of the rack so that I knew for sure that I had it positioned correctly.
The part and shipping cost about $70. It would have cost more than 3 times as much if I had to call a repairman.

The cost part plus shipping for each piece which was described as not cleaning properly due to not spraying. Each of these prices is part plus shipping, diverter valve $28.32 diverter motor did not fix the problem diverter motor $125.08 did not fix the problem my next option is the motor assembly which comes out to $311.53. I think they l ... Read more ead you on with the little parts and you work your way up with the big ones expense wise at this point I will simply cut my losses and buy a new dishwasher because I'm almost at what it would cost for a new one and I've had this one for 4 years. When I went to look for what the problem was each one of these said not cleaning properly which I think now is a generic term to just go from the smallest to the largest if I'm going to replace the motor for 300 plus dollars I might as well just buy a new washer

it was ok if I would have been sent the correct part, but you sent me the wrong part # and I had to go to the post office and mail it back. the part was not the same number as my order and completely wrong, still waiting for my refund and shipping charges. So you have failed me.