EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KDFE204ESS2 KitchenAid Dishwasher - Instructions

All Instructions for the KDFE204ESS2
106 - 120 of 541

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dishwasher door leaking
4 of 4 people found this instruction helpful.
  • Paul from HGHLNDS RANCH, CO
  • Really Easy
  • 30 - 60 mins
Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.
Was this helpful?
Thank you for voting!
The Adjuster tabs broke on both sides
5 of 7 people found this instruction helpful.
  • Michael from MIDLAND, MI
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).

Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.

As practice, I too k one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.

When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.
Was this helpful?
Thank you for voting!
Water leaking at the door during the wash cycle
4 of 4 people found this instruction helpful.
  • Bruce from VERONA, KY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers
The rubber door seal was easy after watching the video. I key point however is that you do have to stretch the seal just a little bit. The video says not to. If you don't like I didn't originally, the seal will only extend from one side to the other without about an inch excess that folds on the bottom of each side. The door still lea ked a little without the excess folded on each side. I did one side at a time and pulled out the new seal along the side before curving to the top, and just stretch it slightly to allow the excess. This stopped the leak.

The lower door seal was ok to do. The most important step there is to remember how the front door panel is installed. Taking pictures before and during removal may help. It is awkward to do by yourself, but can be done. I found that putting a balled-up towel at the top of the door helps when trying to reinstall the front panel.
Was this helpful?
Thank you for voting!
The little ball bearings were droping into the bottom of the diswasher from the tracks.
4 of 4 people found this instruction helpful.
  • James from KNOXVILLE, TN
  • Easy
  • 30 - 60 mins
  • Socket set
I basically used the instructions provided with the "Your Order Has Shipped: email from you. It was quite easy. Thank You!.
Was this helpful?
Thank you for voting!
Dishwasher door falls when opened
5 of 7 people found this instruction helpful.
  • Mark from Seattle, WA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Wrench (Adjustable)
First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there w as so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
Was this helpful?
Thank you for voting!
Left side dishrack track broke. Wanted to install new one.
5 of 7 people found this instruction helpful.
  • Stacey from VESTAVIA, AL
  • Difficult
  • More than 2 hours
Thought this would be much easier than it actually was. Long story short, ended up calling is an appliance professional to install the part.
Was this helpful?
Thank you for voting!
Water leaking around door and latch mechanisim seems to have failed
6 of 10 people found this instruction helpful.
  • Robert from PORT LUDLOW, WA
  • Difficult
  • More than 2 hours
  • Screw drivers
Still not sure it is repaired. Still have water leakage around upper edge of door on control data panel. We just experienced an issue with the auto drain system, the first since door seal repair and door latch replacement???? Is the latching mechanism suppose to secure the door?
If so it isn't?
Not a great success story. A new washer may be in the cards
Was this helpful?
Thank you for voting!
dishwasher would not drain
5 of 7 people found this instruction helpful.
  • Gene from SKYKOMISH, WA
  • Easy
  • 1- 2 hours
  • Screw drivers
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
Was this helpful?
Thank you for voting!
A mouse was chewed through the hose and ate part of it. Di
5 of 7 people found this instruction helpful.
  • Michael from NEW HOPE, PA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
Was this helpful?
Thank you for voting!
If I can do it, you can do it.
4 of 4 people found this instruction helpful.
  • Ellen from GREENWICH, CT
  • Easy
  • Less than 15 mins
  • Screw drivers
Replacing the rear wheel assembly isn't as easy as replacing the front, which took 5 minutes. You have to align the tine row, so it takes a few minutes more. But I'm a tiny woman with long nails, and if I can do it, you can do it!

Just watch the video, follow the directions, and you can't go wrong.
Was this helpful?
Thank you for voting!
Door seal leaking because items from silverware basket damaged the seal while sliding the bottom tray back into the dishwasher.
4 of 4 people found this instruction helpful.
  • Keith from WASECA, MN
  • Really Easy
  • 15 - 30 mins
Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.
Was this helpful?
Thank you for voting!
Upper dishwasher rack broken
4 of 4 people found this instruction helpful.
  • James from ELGIN, OK
  • Really Easy
  • 15 - 30 mins
Removed the old rack clips from the top rack, freeing the rack and removed the bracket holding the adjustable bracket

Replaced the rack bracket and hung the rack back onto the rails
Was this helpful?
Thank you for voting!
A plastic retainer pin for the bottom kick panel was missing.
4 of 5 people found this instruction helpful.
  • Todd from ROTONDA WEST, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Shar pee marker before installation.
Was this helpful?
Thank you for voting!
Tine Row Rusted
4 of 5 people found this instruction helpful.
  • Cheryl von der from HUNTINGTN BCH, CA
  • Very Easy
  • Less than 15 mins
At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.
Was this helpful?
Thank you for voting!
Housing outer piece was broken
4 of 5 people found this instruction helpful.
  • Larry from MANCHESTER, NJ
  • Very Easy
  • Less than 15 mins
Removed old housing parts and replaced them with the new parts I ordered. Very easy
Was this helpful?
Thank you for voting!
All Instructions for the KDFE204ESS2
106 - 120 of 541