KDFE2 Dishwasher - Instructions

I watched the YouTube video I found in the link provided but PartSelect and followed the steps shown in the video. I replaced the two broken rack adjusters in about 20 minutes. I especially like the fact that PartSelect helped with the link provided in the email that acknowledged the part order. A great customer service. I’ve passed thi ... Read more s fact on to my other friends who routinely DIY repair projects.

Removed new from box and installed rollers as instructed that's all there was , very easy.

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.

all 4 wheel units needed to be replaced, popped them off and installed need wheel units in roughly 10 minutes, no tools needed.

Purchase 4 roller wheel assemblies and installed them with only a screw driver to open the tangs. quick and easy and rack rolls smoothly inside the dishwasher. Rather expensive $58 per roller assembly and hopefully these last the lifetime of the dishwasher.

Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack

It was easy to remove the old parts by using a screwdriver to push in “tabs” that kept retainer clips in place. Once removed, it was a matter of easy assembly in reverse and then re-clip. It became clear that the problem was because a few tabs that click into the sliding track and worn to the point where they no longer retained a tight co ... Read more nnection to the track causing the upper rack to tilt with weight to front or back. Sure, the parts are a bit pricey but not when compared to a repair visit or a new KitchenAid which otherwise was functioning perfectly.

Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.

I searched for another dishrack that was compatible with our unit. After measuring and searching online I found Partselect website and placed the order. It was a very easy process. I bought the rack without wheels and just removed the ones from our current bottom rack and put them on the new rack.

The repair was easy. First remove the entire rack from the dishwasher. There are three clips that hold the rack adjuster in place. It's relatively easy to see how to loosen the clips to remove the old rack adjuster. I took a couple of photos before I loosened the clips to help remember where they belong. When putting the rack adjuste ... Read more r it's important to move the rack height adjustment release lever up and down until the vertical part of the rack adjuster easily slides into the slot in the upper rack bracket. Once the rack adjuster in in it's proper location replace the three clips removed at the start of the procedure. Place the rack back into the dishwasher.

I turned off the power to dishwasher first. Removed bottom plate to get to leveling legs. Lowered the legs as to be able to pull and skid dishwasher out from under counter.
Once dishwasher is removed from under locate the 4 screws on right side that hold racks remove them.
I would recommend replacing both skids on both si ... Read more de while you have the dishwasher pulled out.
Very easy to replace new rack slid once old rack removed.
The rack come assembled with skid and plastic holders.
This repair is a 10 minute repair per side.
Thanks Bob Seese

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

Pulled off old seal. Pressed into groove the new door seal. No parts required.

push the 2 retaining clips back with my fingers and slide off the broken roller piece. Slide the new replacement 2 roller piece into place and push up until the retainer clips click and lock.

First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I rei ... Read more nstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!