- Home
- KCCC151DWH1
- Instructions
KCCC151DWH1 KitchenAid Trash Compactor - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Pushed button, made a buzzing noise, nothing happened.
2 of 5 people
found this instruction helpful.
-
Adrien from East Freetown, MA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the driv
... Read more
e gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.
Read less
Was this helpful?
Thank you for voting!
Compactor won't stop
1 of 2 people
found this instruction helpful.
-
Jane from LUTHER, OK
- Easy
- 30 - 60 mins
-
Nutdriver
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (
... Read more
GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
Read less
Was this helpful?
Thank you for voting!
unit was missing parts
3 of 9 people
found this instruction helpful.
-
Richard from glendale, AZ
- Really Easy
- 15 - 30 mins
Installed new parts. Worked fine.
Other Parts Used:
Was this helpful?
Thank you for voting!
Bought a washer without front leveling feet
1 of 3 people
found this instruction helpful.
-
Rick from Lennon, MI
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this helpful?
Thank you for voting!
ram would stop where ever you let go of switch
1 of 3 people
found this instruction helpful.
-
ROBERT from KERRVILLE, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
replaced rotatory switch (10mins) problem solved
Was this helpful?
Thank you for voting!
Plastic Gear Wheel Broke
1 of 3 people
found this instruction helpful.
-
Reagan from Glenshaw, PA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from i
... Read more
ts side. Test.
Read less
Was this helpful?
Thank you for voting!
motor gear broken
1 of 3 people
found this instruction helpful.
-
Clem from Scottsdale, AZ
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of
... Read more
a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....
Read less
Was this helpful?
Thank you for voting!
Ram quit moving
0 of 1 people
found this instruction helpful.
-
Hal from Granada Hills, CA
- Easy
- 30 - 60 mins
-
Nutdriver
Removed bottom and replaced gears
Was this helpful?
Thank you for voting!
Compactor ram was stuck in the down position and door would not open
0 of 1 people
found this instruction helpful.
-
Michael from South Boston, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening
... Read more
the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!
Read less
Was this helpful?
Thank you for voting!
Broken Drive Gear
1 of 4 people
found this instruction helpful.
-
Michael from Painted Post, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
roller bearing for trash bin was damaged and would not allow canister to roll
6 of 32 people
found this instruction helpful.
-
roberto from keller, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
the bearing were the perfect match and instructions helpful. sysem is rolling smoothly
Other Parts Used:
Was this helpful?
Thank you for voting!
my compactor container was badly worn out
-
Richard from East Wenatchee, WA
- Really Easy
- 1- 2 hours
-
Screw drivers, Socket set
All I really needed to do was to take the front facing off and put on the new container, but I took the opportunity to do a complete overhaul and cleaning. It now work like a new compactor.
Was this helpful?
Thank you for voting!
Large ring gear - delrin - split in two
-
Chris from Burlington, CT
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Socket set
Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed f
... Read more
rom the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.
Read less
Was this helpful?
Thank you for voting!
Trash compactor would not turn off at end of cycle and made a grinding noise and some vibration
-
Ronald from Brentwood, TN
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screw
... Read more
s from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .
Read less
Was this helpful?
Thank you for voting!