EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KCCC151DWH0 KitchenAid Trash Compactor - Instructions

All Instructions for the KCCC151DWH0
61 - 75 of 128

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
One of the nuts on the ram stripped out
1 of 2 people found this instruction helpful.
  • kelton from weatherford, TX
  • Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
1)Pulled the unit out remove the top and bottom covers. 2)Disconnected the drive chain by removing the sproket from the motor. 3)Unscrewed the drive rod on the side that worked and removed the ram. 4)Reassembled and used the bin for trash while waiting for the part. 5)The nut came with clips included (this was not noted in the order but i s vital) removed the stripped nut by breaking the old clips. 6)Installed the new nut, clips on the ram. 7)Installed the ram onto both drive screws. I had to hold the 'top sensor' switch up to reverse the screws to lower the ram. 8)Rinstalled the top and the appliance. 2 thru 4 dealing witht the chain, sproket and screw were fairly complicated operations.
Was this helpful?
Thank you for voting!
Pushed button, made a buzzing noise, nothing happened.
2 of 5 people found this instruction helpful.
  • Adrien from East Freetown, MA
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the driv e gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.
Was this helpful?
Thank you for voting!
Compactor won't stop
1 of 2 people found this instruction helpful.
  • Jane from LUTHER, OK
  • Easy
  • 30 - 60 mins
  • Nutdriver
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong ( GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
Was this helpful?
Thank you for voting!
unit was missing parts
3 of 9 people found this instruction helpful.
  • Richard from glendale, AZ
  • Really Easy
  • 15 - 30 mins
Installed new parts. Worked fine.
Was this helpful?
Thank you for voting!
ram would stop where ever you let go of switch
1 of 3 people found this instruction helpful.
  • ROBERT from KERRVILLE, TX
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
replaced rotatory switch (10mins) problem solved
Was this helpful?
Thank you for voting!
Bought a washer without front leveling feet
1 of 3 people found this instruction helpful.
  • Rick from Lennon, MI
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this helpful?
Thank you for voting!
Plastic Gear Wheel Broke
1 of 3 people found this instruction helpful.
  • Reagan from Glenshaw, PA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from i ts side. Test.
Was this helpful?
Thank you for voting!
motor gear broken
1 of 3 people found this instruction helpful.
  • Clem from Scottsdale, AZ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....
Was this helpful?
Thank you for voting!
Compactor ram was stuck in the down position and door would not open
0 of 1 people found this instruction helpful.
  • Michael from South Boston, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!
Was this helpful?
Thank you for voting!
Ram quit moving
0 of 1 people found this instruction helpful.
  • Hal from Granada Hills, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver
Removed bottom and replaced gears
Was this helpful?
Thank you for voting!
Broken Drive Gear
1 of 4 people found this instruction helpful.
  • Michael from Painted Post, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people found this instruction helpful.
  • Howard from Boynton Beach, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol oring refer handles. Thank you
Was this helpful?
Thank you for voting!
roller bearing for trash bin was damaged and would not allow canister to roll
6 of 32 people found this instruction helpful.
  • roberto from keller, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
the bearing were the perfect match and instructions helpful. sysem is rolling smoothly
Was this helpful?
Thank you for voting!
The compactor was loaded with too many wine bottles
  • james from Milton, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers
At best it is advisable to load just one at a time and covered with newspaper etc., In this case someone put in three bottles with out covering with heavy newspaper etc.and for some reason one rode out and to the side. Crushing the side of the metal trash container. This pinned the container against the side of the compactor body and behi nd the front rails. Using a lot of pulling and some nifty pry bars and two hours of prying and squeezing we got the container out( see attached photo )The replacement container was ordered on a Sunday night and arrived Tuesday morning. Removal of the existing front panel ,foot pedal and door switch was easy and installation on to the replacement container was a breeze with a little orientation required to line up the switch and pedal in the right configuration. 20 min tops and that was with five kids helping ;)
Was this helpful?
Thank you for voting!
Primary Power Transfer Gear Split in Half
  • Robert from Willow Creek, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Compactor ram was stuck in the down position after hearing a loud bang during a compacting cycle. Removed outer compactor casing to determine cause, only to find gear housing underneath the compactor that contained drive chain and gear assembly. Primary gear had split neatly in half. Determined the appropriate part needed with partsele ct part finder (of course, an entire kit, and not just the gear), had part shipped and had compactor repaired in three days. The actual repair and reassembly of the compactor took less than a half-hour. Consisted of removing chain tension from gear hub by loosening four sheet metal screws holding motor assembly, removing circlip and old gear hub from chain and shaft, replacing gear hub with new part, lubricating the gear mechanism, and reinstalling in reverse order.
Was this helpful?
Thank you for voting!
All Instructions for the KCCC151DWH0
61 - 75 of 128