KCC1500 KitchenAid Trash Compactor - Instructions

I held up on the compactor ram as i loosened the two screws on each of the two retaining cups. I then unscrewed the threaded bushings and lifted the ram out of the unit. I then cleaned the surface of the tracks on which the ram guides up and down and applied a thin layer of silicone grease to those surfaces as well as the threaded rods ... Read more . . I placed the ram back into the unit and held it in place as i replaced the threaded bushings and their respective caps. Unfortunately i neglected to move the limiting switch that stops the ram when it reaches the top of the cycle and I broke the lever that contacts the ram and subsequently activates the stop switch. so i removed the ram and removed and inspected the switch. It was broken beyond repair so i ordered a new switch from the same place I purchased the threaded bushings and am waiting for them to arrive. Lesson learned, pay attention to the sequence by which the original parts are removed and understand how the system functions so that you can remember to put it back in the right order.

Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.

The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.

Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.

Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.

Removed two screws on back of pull out door. Pulled up on handle, came out easily, slide the new one in, replaced the screws and done. Less than 5 minute repair.

Removed and replaced in less than 15 minutes. Works like new again

There were two screws holding the handle on, We removed the two screws, removed the broken handle and screwed the new handle on.

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

Took under 5 minutes to unscrew old handle and screw on the new one. Identical part to old handle, compactor looks and works like new!

I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less ... Read more than 30 minutes including cleanup.The wife happy,that all that matters.
Jack

Unscrewed old one. Slide new one in. Screwed in two screws. Done. The handle ended up being black, even though the part was listed as brown.... that is good, because the original part was black.
So glad you had the part. It was pricey, but way less than a new trash compactor!

It is held on with three screws. The PartSelect was the only web site that showed me a picture of the part I wanted. The other web sites said it was no longer made. It was shipped out the day I ordered it, and took a minute to install it. Will order again from your company - great service - thanks.

I pulled the unit out and tipped it over . I pulled the pan off the bottom then i could put a box end wrench on the screw that was jamed then tuned the screw to loosen the door . i then removed the plastic bag that was wrapped around the screw and put the new nut on and all fixed

Removed drawer
Pulled out from cabinet
Unplugged power cord
Removed top cover
Removed front panel
Put front on 2x4 block
Unscrewed leveling legs
Used 9/16" socket to remove old rollers
Installed new rollers
installed front panel
installed top panel
Plugged in electric cord
slid b ... Read more ack into cabinet
inserted drawer
tested
Works as good as new