KBRS19KTWH00 KitchenAid Refrigerator - Instructions

Took too panel down. Remove.bulbs . Unplugged refrigerator. Removed electronic control board .installed new electronic control board. Plugged in refrigerator , programmed control for ice in about 1 hour refrigerator went to work and got cold Simple operation. Donald Harrell, Don's Repair Service .

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

Plied off the relay switch with a screw driver. I could not pull it off by hand. Disconnected the wires to it and replaced with new part. Had problem getting the part back on and lining up the pins with the connector. I had to line up one pin and start at an angle and roll the part onto the contact pins.
I was impressed with the one ... Read more day delivery without paying because it was shipped from a warehouse in California where the repair was made.

Unscrewed back of fridge and unplugged relay from compressor and plugged in the new one remember that the new one turns 180 degrees from existing switch.

First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector ... Read more was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble ... Read more the refrigerator, it was fully operational. Very easy to do and only required a few tools.

Removed back access cover with quarter inch nut driver, unplugged wire harness, pulled old relay out & plugged in new one, reconnected wire harness, and reinstalled access cover. Piece of cake. (Shipping was very quick) ***Frig was only 3yr an 1 mounth old.*** Maytag - Dependable Huh?

Once I got the right part the repair was quick and easy. All I had to do is get the old part off with a screwdriver and curved needle nose pliers and the old part came right off. The new part went in just as easy. Quick and easy. Less than 15 minutes.

The repair was just unpacking the glass and placing it on the frame inside the refrigerator. Unfortunately, the shelf was listed by photo and not dimensions for the model number submitted and is approximately 2 inches short. Had I known the dimensions ahead of time, I would not have placed the order.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was ava ... Read more ilable. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

I searched the internet for the correct part and reviewed the instructions on the internet. Upon ordering the correct part I was provided a link to a video that walked me through step by step. The very first thing I did was unplug the refrigerator.I then located the control board located in the housing in the ceiling of the refrigerator. ... Read more Using a screwdriver I was able to carefully separate the housing from the refrigerator ceiling . Unplugged the housing and then had to separate the plastic housing to locate the control board. Ran into a little difficulty at first separating the plastic tabs but with a screwdriver carefully pried the tabs. Once completely open is where the control board was. More plastic tabs holding the control board in place. Carefully separated the board from the tabs. The were two plugs that needed to be separated from the board. Used a screwdriver to get the plugs separated.The new board you had to bend carefully at a joint so the board became two pieces. Snapped the boards in place. Plugged the board in two spots. Put the housing together and put the housing in place in the refrigerator. Plugged the refrigerator in. All lights came on and then had to program the board. The instructions were spit on. The code is located inside the fridge were the model tag is. Programmed correctly. Word of advice read the directions a few times you can't go wrong. So far it's day 7 after I installed the board and no ice building up. According to the internet the control board controls the defrost function on my model. Very happy. I'm still watching the freezer but I'm pretty sure I fixed my matter. Thanks for sending the right part and the video. Repair went well. Just take your time and go easy because everything involved is plastic. I didn't want to break any tabs I had to deal with.

On the back of the refrigerator, I unscrewed and removed the lower-right panel. As I peeled the insulation off the panel, the insulation would disintegrate, so I used a vacuum-cleaner hose to remove most of the insulation. I removed the remaining adhesive with my fingers. I peeled the backing off the new insulation, and stuck it to the pa ... Read more nel.

I had ordered two pieces of insulation, hoping to also replace the insulation behind the compressor, but removing the compressor was complicated and risky, so I returned the second piece of insulation.

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed