KBLS36MHX00 KitchenAid Refrigerator - Instructions

Determined that compressor was not running, after researching problem on another site they recommended i try the condenser moor fan or motor, the defrost thermostat or defrost timer. . I was not satisfied with their recommendations. If I had tried their recommendations i would have likely gotten frustrated and spent upwards of $3000 to ... Read more replace the 22 year-old hand me down unit. Thank you Parts Select for properly diagnosing my relay failure saving me a ton of money.

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of ... Read more scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.

Very easy to order from parts select. Took seconds to replace.

I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.

ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80.. ... Read more .would have been at least $100 to have a repair person come to the house!

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) re ... Read more move the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for ... Read more several hours/days. You will have to defrost to begin making ice again.

Turned off power to Frig.. Removed shelving & baskets, then removed cover concealing fan, with cordless drill & proper size bit. All work done with the same size bit. Wrote down where colored wires came from so I could put the back in the right place. Piece of cake!!

We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.

This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.

These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.

I replaced the old icemaker with a new one but the problem is still occurring in the new one. It only fill with enough water to make about two ice cubes

Followed on line video

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.