KBFS25EWWH1 KitchenAid Refrigerator - Instructions

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

first pressed in two bottom corners then used fingers to press in bottom section,pressed in two top corners then pressed in both sides using fingers followed by pressing in top section using fingers.VERY EASY !

Pulled out on gasket seal at top right corner of door and when loose pealed the seal out around door. Installed gasket by inserting channel insert into door groove and pressed gasket in while lightly pulling down to stretch seal out to facilitate inserting gasket lip into door channel. Bada bing! Done. Good fit. Note: I laid out gasket in ... Read more the sun to soften it up as there were some small wrinkles in material from being folded for shipping. Hair dryer would work too!

Watched installation Video on the website parts. I put the new gaskets in bath tube in warm water for a few minuets until the gaskets were warm and pliable. I removed old gaskets cleaned door facing and installed new gaskets as instructed on video. Thanks for the information on how to install because I was dreading trying to do this task. ... Read more "Just follow and listen to the instruction on Video".

replaced the poorly designed "duck bill" drain with this P trap. Very simple repair done by accessing through the back of the refrigerator. The video on this website walked me right through the repair. It did however fail to mention that the ice has to be removed from the inside. I had to remove the drawer face and pull outs. Then the ice ... Read more maker and back panel are removed. I used a heat gun and screwdriver to chip and melt the ice build up. If one had the luxury of having another refrigerator to move food in to you could just unplug the unit until the ice melts.

Remove the existing mullion rail:

- Remove the screw from the center hinged cover.
- Remove the mullion rail by pushing upward. The top and bottom hinges slide over tabs attached to the door. I had to bump it gently from underneath.
- Disconnect the three wire connector that's underneath the center hinged cover.
... Read more
Install the new mullion rail by reversing the above steps:
- Connect the three wire connector and snap it into its holder.
- Slide the new part over the top and bottom hinges. Be sure that all three hinges are correctly lined up before sliding the rail over the tabs.
- Push it down far enough that the hole for the screw in the center cover is lined up with its corresponding receptacle in the door.
- Replace the screw.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Just pulled out theold and squeezed in the new. I forced it and it went in.

Removed the middle screw and the whole rail came of. Unplugged wires and removed old rail. Plugged in the new rail and slid top and bottom slides on and put on the middle screw. Job finished

I ordered a right & left gasket but when they arrived there was no indication of which was the right or left one...so I just had to guess...I easily lifted the old gasket away from the door & removed. Then starting at the top began inserting the portion that goes into the groove with the help of the table knife, continuing down both sides ... Read more ..then sat on a stool to push the bottom section into place...Had to go back over several areas to reseat but finally closed the door to hopefully set the gasket..Drank some hot tea, then removed the left gasket & began the process all over...The extra flaps ended up on the left side of the door so I may have to remove this side and reposition...I'll check it in a few..then will blow all with a warm setting of the low dryer to continue helping the molding process..

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert th ... Read more ermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

Broken bottom drawer lid mount

It was a very simple operation and was done in no time.

Doing it myself saved me at least $100.00 or more.

I was very happy and satisfied with the part and how doing it myself saved me a lot of time and money.

I broke the left side end cap the holds the pantry door on.
I search the internet for the part and happened to run across part select. I order the part and received the part with in 3 business days. It took less than 30 minutes to replace the end cap.

The great reviews help me with my choice to order the part from part sel ... Read more ect. I will order parts from them again.

Thanks for helping me fix my fridge.