KBFS25EVMS00 KitchenAid Refrigerator - Instructions

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

Easy site to locate your part. Arrived at my house quick and installed very easy. If I ever need another appliance part I will be coming back to partselect.com!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Removed ice maker.

Bottom freezer made access a tad awkward.

New unit did not come with wiring harness, or wire rod that activates cycle, or the front cover, which required transferring those items from old unit. Instructions on internet did not address this.

Installed new unit.

Removed the chiller level and ice bin exposing the icemaker assembly.
Unplugged the icemaker assembly electrical connecter.
Used the nut driver to remove three screws that fasten the icemaker assembly to the refrigerator side wall and angle bracket.
Removed Ice tray assembly.
Reversed the steps to install the new icemaker.
Cured the problem.

I used a nut driver to remove the screws and took out both right and left end caps and put in the new ones it was so easy I couldn't believe it.

This is definitely one of the easiest, most rewarding projects I've ever done! From the point of easy ordering to receipt of the part in just two days (!!!!), opening the box was probably more effort than clipping the part in place! I'm keeping partselect on my favorites list!

Remove the glass shelve and the lower drawers. Remove the support rods front and back. Remove three screws from the end cap. Replace end cap and replace all other parts in order. Reattach the drawer cover by putting in one side and then bending the pivot slightly to insert the otheer side.

This refrigerator is one of our company refrigerators and takes a beating. The center rail that holds the drawers had been broken. The repair was as simple as sliding the broken rail out and sliding the new on in place. It was as easy as it gets.

I pulled out the slide out drawer the shelf on top of it too a nutdriver and remove the broken panel while the daughter-in-law cleaned out the drawers. popped the new back in a srewed it back. It was so easy I could not believe it. I am 65 and a woman!!! I was done way before my daughter-in-law was finished cleaning. LOVED IT!!!!!!
Thank you so much for this wonder website. Barbara from lake worth,fl

Pulled out the meat tray drawer and crispers above and removed the sheet of glass between them. Removed the nuts holding the old pantry end cap and replaced with the new one. Replaced glass, crispers, and meat tray drawer. Very quick and easy. Delivery was unbelievably fast.

Side by side refrigerators are tough to get two arms inside the freezer side (and do much work) especially to unlatch the power connect. The water tube on this old refrigerator feeds from the back so I took a pair of kitchen shears and made a new opening in the back of the catch basin. Sealed the original opening. Don't know if that was necessary. The video was a big help for this parts change. Much easier than expected. G Keen

It took longer to take the items[food] out than to repair. It was very easy to replace.

Disconnted current icemaker and removed from freezer. Took off front cover and long arm that control ice dispenser. Put cover and control arm on new icemaker, reconnected bundled wires into new icemaker and clipped along side of icemaker and remounted into freezer. Connnected into back panel for power and checked water supply line to make sure it was lined up properly and job was done. Made sure arm was in down position, had ice cubes in an approx 90 mins.

First all product had to be removed in order to remove glass top that cover the crisper drawers, then removed both drawers and thenremoved the broken Crisper Frame Center Rail and installed the new part. Even with cleaning everything and putting it back together the whole job was only about twenty minutes of work time. Best thing of all was the price for the part, I will try to use PartSelect item for any other repairs I do on my appliancce!!