Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
little hinge thingy that holds pantry door snapped off
7 of 9 peoplefound this instruction helpful.
Allyn from los angeles, CA
Really Easy
Less than 15 mins
Screw drivers
Removed the three screws that held part, lifted and removed old part and replaced with new piece. Couldn't have been easier. Saved me the $100 the repair man quoted me. Cannot believe it was so easy and the part was soooo affordable! Thank you very much for the speedy delivery. It came within days of my order. I will use y
... Read moreour service again for sure! Thank you! Allyn Rosenzweig
Read less
Was this helpful?
Thank you for voting!
Refrigerator would cool for a very short period of time. Then the compressor would shutdown via internal thermal overload or high head pressure. This was caused by the lack of airflow across the condenser coils and compressor.
10 of 18 peoplefound this instruction helpful.
Daniel from RICHTON, MS
Very Easy
Less than 15 mins
Nutdriver, Pliers
(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed
Was this helpful?
Thank you for voting!
Replace crisper drawer
7 of 9 peoplefound this instruction helpful.
Eric from Stanardsville, VA
Really Easy
Less than 15 mins
The front had to be removed from old drawer a put on new one
Was this helpful?
Thank you for voting!
Button holding snack drawer cover was broken
6 of 6 peoplefound this instruction helpful.
Claude from Phoenix, AZ
Really Easy
Less than 15 mins
Screw drivers, Socket set
1. removed both bottom crisper drawers 2. removed glass shelf under crisper drawers 3. removed shelf support pieces 4. removeded snack drawer 5. removed left slide rail using phillips screwdriver (2 screws) 6. removed LH end cap using socket wrench (3 screws) 7. attached new LH end cap 8. attached slide
... Read morerail 9. installed glas shelf supports 10. installed glas shelf 11. install bottom crisper drawers 12. install snack drawer 13. install snack drawer top
total time was less than 15 minutes
Read less
Was this helpful?
Thank you for voting!
Glides easy to install, about 15 minutes
9 of 15 peoplefound this instruction helpful.
Mary Sue from Tinley Park, IL
Easy
Less than 15 mins
Screw drivers
you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.
Was this helpful?
Thank you for voting!
broken light switch in the freezer
6 of 6 peoplefound this instruction helpful.
kathleen from GREEN VALLEY, AZ
Easy
Less than 15 mins
Screw drivers
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
Was this helpful?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
7 of 10 peoplefound this instruction helpful.
Antonio from San Antonio, TX
Really Easy
Less than 15 mins
Screw drivers
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this helpful?
Thank you for voting!
No problem
5 of 5 peoplefound this instruction helpful.
Rodney from LAVEEN, AZ
Very Easy
15 - 30 mins
Just pulled the old one off with fingers, and pressed the new one in place.
Was this helpful?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
5 of 5 peoplefound this instruction helpful.
Duncan from Metairie, LA
Really Easy
Less than 15 mins
Screw drivers
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this helpful?
Thank you for voting!
Fridge had a clicking noise
5 of 5 peoplefound this instruction helpful.
Theodore from JACKSON, WI
Very Easy
Less than 15 mins
Screw drivers
Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.
Was this helpful?
Thank you for voting!
Gasket has 2 tabs on the side that opens. Both had torn. Also one vertical slit halfway up the gasket
5 of 5 peoplefound this instruction helpful.
William from BRUCE TWP, MI
Very Easy
Less than 15 mins
Followed your instructions: gasket came coiled in the box and was slightly curled up. Both left & right side of gasket were linked. Followed your instructions to properly restore the shape. Pulling the old gasket off and installing the new one took just a few minutes
Was this helpful?
Thank you for voting!
My Whirlpool Fridge and freezer would not get cold.
5 of 5 peoplefound this instruction helpful.
Bryce from STUART, FL
Very Easy
Less than 15 mins
Nutdriver
My Whirlpool model (GB2FHDXWS09) Fridge and freezer would not get cold. The compressor would turn on for about 5 seconds and turn off. I called parts Direct and they knew it was the Capacitor right away. I also ordered the Start Relay just to replace it as well, that was my choice.
Received the parts super fast. I chose to pa
... Read morey for faster shipping.
Super great place to shop, watch help videos and get the answers you need for what you need. Super happy with everything about this company and the person that helped me on the phone to place the order and confirm I was ordering the right part.
Done and working. Took me about 5 minutes. Everything is plug and play besides taking a few screws off the back.
Hardest part is access to the icemaker itself. Once I removed the freezer door (bottom drawer freezer), and got the sliding basket out, it was a 10 minute job. Make sure you start the upper screws first, the icemaker will hang there while you adjust, connect the harness, and tighten. Make sure you are ready before you close the door, it
... Read morewill start making ice as soon as the door is closed.
Read less
Was this helpful?
Thank you for voting!
Existing icemaker would freeze up, stop making ice.
5 of 5 peoplefound this instruction helpful.
Steve from WAKE FOREST, NC
A Bit Difficult
15 - 30 mins
Nutdriver, Screw drivers
I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icem
... Read moreaker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.
My Orders
