KBFS20ECWH00 KitchenAid Refrigerator - Instructions

I ordered a right & left gasket but when they arrived there was no indication of which was the right or left one...so I just had to guess...I easily lifted the old gasket away from the door & removed. Then starting at the top began inserting the portion that goes into the groove with the help of the table knife, continuing down both sides..then sat on a stool to push the bottom section into place...Had to go back over several areas to reseat but finally closed the door to hopefully set the gasket..Drank some hot tea, then removed the left gasket & began the process all over...The extra flaps ended up on the left side of the door so I may have to remove this side and reposition...I'll check it in a few..then will blow all with a warm setting of the low dryer to continue helping the molding process..

Unplug the electric flat plug from wall. Loosen up 3 mount support screws , Change out unit. Mount Int back onto 3 support screws . Plug in electronic flag plug , It only goes in one way since the plug as a grove on it.

I first removed the door to the freezer (my frig has a bottom freezer) by loosening the 4 screws and lifting the door up and off. Then, because I'm stubborn, I chose not to remove either of the basket/drawers. It took a little bit of effort to fit my arms/hands in there, but I was able to remove the bottom screw to the old icemaker, and loosen the two top screws. (And disconnect the wiring harness.) I could then lift the old icemaker up and off. Putting the new icemaker in was pretty easy-- just slide it down over the two top screws and connect the wiring harness. The hardest part was getting the bottom screw back in! Because I didn't remove the baskets/drawers, I had very little room to work, and I had to "feel" for where that bottom screw went (even used a little mirror to help me). I could have just left this screw out, as the icemaker was sitting in there quite securely. But I kept at it, and after about 20 minutes, I was able to line up the screw with the hole, balanced on the tip of the screwdriver, and get it screwed in. Total repair took about 45 minutes. And no more leaky ice maker!

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

After watching a couple of YouTube videos I had an idea of what to expect. It is really easy. Simply pull out the old, clean up the track and press in the new. I used a heat gun to eliminate the wrinkles in the material. A hair dryer would work as well.

I turned the light bulb into the socket

Loosen 4 screws remove door wipe off frost pull old gasket out of slot push in new gasket instal door that was it. No help need.

take the old one out replace with new once - no instructions required, no tools needed

Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

You just take the old door bin out by sliding it up and replace with the new bin by sliding it down in the door.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

The old gasket peeled out easily. No tools needed. The replacement gasket fit right in the groove. I did not need to immerse the gasket in warm water or use a hair dryer. Nifty trick: once the new gasket is in place, close the freezer door. Run your finger in the center groove of the gasket, which will push the magnet against the fridge. Leave the door closed for an hour. The gasket has then assumed a perfect fit and will continue to fit perfectly.

Awesome! Couldn't ask for it any better. I watched the video from Partselect multiple time and was just as easy as they said it would be. It took me longer to watch the video four times than it did for me to install it. I have a habit of 10 minute projects turning into a couple hours and this took about 10 minutes. Thanks.

Followed your instructions: gasket came coiled in the box and was slightly curled up. Both left & right side of gasket were linked. Followed your instructions to properly restore the shape. Pulling the old gasket off and installing the new one took just a few minutes