KBFA KitchenAid Refrigerator - Parts

This is just the bottom glass cover for the crisper drawers. It does not include the frame.

This long harness thermistor kit is what helps monitor and regulate the temperature inside your refrigerator. It can be located in either the freezer compartment near the evaporator coils or in the fresh food compartment near the airflow channels, depending on the model. If you notice issues like excessive icing in the freezer, inadequate...Read more cooling in the refrigerator, temperature fluctuations, or error messages on the display panel, it indicates a potential problem with the thermistor. Since your fridge will not be able to maintain the desired temperature, this results in food spoilage, inefficient cooling, and potential damage to the cooling components. To replace the thermistor, disconnect it from the connector plug or wiring harness and remove any mounting brackets or clips using a screwdriver if necessary. Remember to consult your user manual to determine the required number of thermistors, as they are sold individually as OEM replacement parts.

This part mounts on the crisper drawer cover and is used to limit the amount of air that gets into the crisper.

This is a replacement pivot block for your refrigerator. It is made of white plastic and is approximately 4 inches long and 1 inch wide. The pivot block catches and holds the door mullion cover when you close the door. If your refrigerator door will not close properly, you may need to replace the pivot block. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Commonly referred to as the flapper assembly, the door mullion is an important part of a double, or triple door refrigerator.

The icemaker shut off arm, used in a refrigerator, gives the icemaker a signal to stop making ice once the bin has a reached a certain limit. This helps monitor ice production. If your icemaker is not making ice properly or consistently, replacing this part could be a solution to your problem. The tools required for this installation are ...Read morea 1/4 inch nut driver, a Phillips screwdriver, and needle nose pliers. Refer to the manual guide provided by the manufacturer for further guidance and instructions. Remember to safely store food when the refrigerator power is off to keep it from deteriorating.

The fan blade is used to blow air over the condenser.

These parts will attach to your drawer rail and are used to help the drawer glide smoothly.

This door gasket is for refrigerators. The door gasket is on the inner door panel and creates a seal around the door to prevent warm air from entering the refrigerator.

The ice bucket in your freezer catches and holds the ice when it is released by the icemaker. If your ice bucket is cracked or damaged, you may need to replace it to prevent a potential leak. This part is made of white plastic and is sold individually. This ice bucket is approximately 15 inches long by 12 inches wide. Many of our customer...Read mores have rated this repair as very easy. To complete this repair, simply remove the old ice bucket and replace it with the new one. Be sure to remove any broken pieces of the old ice bucket before replacing it.

This defrost thermostat is a temperature sensing mechanism used in freezers and refrigerators. The thermostat senses the rise in evaporator temperature during a defrost cycle and turns the defrost heater off once frost is melted from the coils. If the freezer is not defrosting, or the freezer section is too warm, it is best to replace the...Read more thermostat to fix the problem. The tools needed for this project are: 1/4 inch nut driver, flat blade screwdriver, needle nose pliers, wire strippers, and pair of wire nuts. Remember to unplug your appliance from the power source for safety and refer to the manual provided by the manufacturer for installation instructions.

This is an evaporator fan motor, it is 115 volts and 60 hertz and it is for your refrigerator/freezer. You will need to replace this part if your appliance is too warm or getting noisy. This evaporator fan motor is located in the back of the freezer. This part circulates air over the refrigerator coils. These coils will convert the heat i...Read morento cool air, which is then circulated throughout your appliance. To replace this part you will need a 1/4-inch nut driver and a pair of needle nose pliers.