KBBL206ESS01 KitchenAid Refrigerator - Instructions

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Put painters tape next to light, so I wouldn't scratch surface. Worked edge of light down and out of hole with small screwdriver. Chechen wireing , light might work ? Unplugged light assembly . Plugged in new light , and reinserted light into opening . Removed tape ,, done. You can use putty knife in place of screwdriver. Be patient. Go ... Read more ogle helps also.

We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

Our unit is a built-in unit so first had to remove the decorative cover panel to expose the internal on/off switch. Turned off the circuit breaker. Disconnected the wires (simple pull-off/push-on). Removed the old switch which meant clipping the plastic tabs holding the switch in position. Inserted the new switch by simply pushing it thro ... Read more ugh the opening being sure to have it in the same alignment ('off' to the back of the unit.) Reconnected the wires making sure to have a white ground wires on the left and the black 'hot' wires on the right. Turned the circuit breaker back on. Turned the switch on. Now it runs.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

followed the instructions provided and that's it!

I think the lights are wired in series. When the light in the freezer goes bad several lights in the refrigerator go out but are still good. Replace the lamp in the freezer and all the lights in the refrigerator work again. The only tools I used was a 1" scraper and a very small flat screwdriver to pop the lamp assembly out. Not much room ... Read more to work in so it was a bit of a job getting the wire connector where it needed to be but not to bad..

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

There is a good YouTube vid on how to extract the old LED without damaging the liner of the appliance. (Use a one inch plaster spatula and some blue painters tape). VERY IMPORTANT: The freezer LEDs and the one that was out in the fridge compartment are in series on the same circuit. I found out by trial and error after a frustrating start ... Read more . If one or two are bad they all go out like a christmas light string. So be patient and keep replacing bulbs until they all come on. Then you can test each one you took out to see if it was bad or not by putting it back online. At first I was annoyed that Part Select may have sent the wrong replacement items but they were in fact correct. These bulbs are not cheap so make sure the ones you take out are truly burned out.

I removed the cap from the filter pushed a lever and removed fliter. I replaced the old filter, removed the caps on the new one and slid it into channel after replacing the outer cap. I removed water from the spigot for 4 mins. and it was ready to go. I pushed the reset button to get the green light to come on.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Just put the new one in.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Technician at ASK suggested replacing ice maker. Ordered new ice maker(prompt delevery)then noticed it came without wire arm and white platic "flag". Ordered arm and "flag", replaced all old with new and seems to be doing well. Perhaps all I needed was the plastic "flag" on the limit arm wire. Will never know. The new icemaker wiring had ... Read more short wires and a connector. Old ice maker had no connector so the short wires were removed and the old wires plugged into the ice maker. Mirror was required in order to see the side wall mounting screws. Very narrow work area, tiny freezer side.