KB443GDM2 Frigidaire Wall Oven - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cord was not tightened enough by delivery crew.
109 of 174 people
found this instruction helpful.
-
Timothy from Spring Valley, AL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read more
d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read less
Was this helpful?
Thank you for voting!
Oven light receptacle broken - bulb base broke off
69 of 116 people
found this instruction helpful.
-
Paul from Spokane Valley, WA
- Easy
- 30 - 60 mins
-
Screw drivers
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven,
... Read more
and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
Read less
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 people
found this instruction helpful.
-
Lise from CEDAR GROVE, NJ
- Very Easy
- Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
broken lens over oven light
11 of 22 people
found this instruction helpful.
-
Leslie from Warsaw, VA
- Really Easy
- Less than 15 mins
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this helpful?
Thank you for voting!
The elements were not heating up
6 of 8 people
found this instruction helpful.
-
Tanya from KALISPELL, MT
- Really Easy
- 15 - 30 mins
-
Screw drivers
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this helpful?
Thank you for voting!
Refrigerator Light bulb went out
7 of 12 people
found this instruction helpful.
-
ANGELA from MEBANE, NC
- Very Easy
- Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
5 of 7 people
found this instruction helpful.
-
Phyllis from GAINESVILLE, GA
- Easy
- Less than 15 mins
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in
... Read more
the house.....I show them what I DID!! :-)
Read less
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people
found this instruction helpful.
-
Alan from SAN MATEO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
3 of 3 people
found this instruction helpful.
-
Daniel from Falmouth, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Read less
Was this helpful?
Thank you for voting!
Lens cover for the oven light
3 of 4 people
found this instruction helpful.
-
Larry from COZAD, NE
- Really Easy
- 30 - 60 mins
Very easy just had to pull the wire up that holds it secure.
Was this helpful?
Thank you for voting!
Knobs for the three timers on the appliance console deteriorateddue to age.
3 of 5 people
found this instruction helpful.
-
Vincent from Bonita Springs, FL
- Really Easy
- Less than 15 mins
The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.
Was this helpful?
Thank you for voting!
wrong part
2 of 4 people
found this instruction helpful.
-
Barbara from WICKENBURG, AZ
- Very Difficult
- 30 - 60 mins
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as w
... Read more
ell as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Read less
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people
found this instruction helpful.
-
Denise from Landover, MD
- Really Easy
- Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
No Power to the Oven
1 of 3 people
found this instruction helpful.
-
Tony from Hartford, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this helpful?
Thank you for voting!
Lens cover for oven light broke.
0 of 1 people
found this instruction helpful.
-
Amy from Corona, CA
- Really Easy
- Less than 15 mins
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this helpful?
Thank you for voting!