KAWE9 Washer - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.

Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the lo ... Read more ng shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.

While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be ... Read more necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.

Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.

Washer was leaking -- in part from hoses that had loosened over time due to unbalanced loads and age, and partly from a worn pump -- and not agitating/spinning properly. Fixed hoses, replaced pump and clutch. Unfortunately, when I pulled apart direct drive to replace clutch, the drive shaft started leaking because old seals worn and comp ... Read more romised on disassembly. Have to give credit where due -- YouTube invaluable here -- pulled and disassembled drive shaft, removed old seals, replaced and reassembled. Time consuming, but if you keep track of where things go, not too bad. 3 things I wish I knew in advance: (1) for an old washer you definitely need a spanner nut wrench (like 15-25 bucks online) to remove the spanner nut so you can pull the basket and get to the seals -- no wrench/pliers/vise substitute will do the trick; (2) the shaft seals have metal washers inside the rubber/plastic -- when you're removing the old seals, you might need to chisel (hammer and small flat head screwdriver) the old seals out instead of just pulling out the corroded rubber which will leave the old metal behind; (3) if your time is valuable, try to diagnose all the likely sources of your problem and buy the parts to repair at once rather than doing piecemeal like me. Took me 2 weeks and two complete tear downs to finish a repair that should have taken me an afternoon. I love my local Appliance Parts guy -- he's knowledgeable and usu. has what I need or can get it fast and I like supporting local brick and mortar -- but if time is important to you, taking advantage of online companies that allow you to return what you don't use may save you time.

Removed the 2 screws holding the control panel.
Tilt the control panel back to expose the spring clips.
Disconnected the Lid Switch Harness plug from the control panel.
Pry out the 2 spring clips, each located on either side of the top of the cabinet.
Openned top lid, placed one hand into the lid openning and pulled th ... Read more e cabinet forward.
Disconnected ground wire. Installed new switch while cabinet was off. Reconnected Harness connector after re-installing the cabinet.

Removed screws on top of machine to remove the control unit out of the way. Then used large regular screw driver to pry out the two clips that hold the back of the washer tight to the top frame. This allows the back to come away from the machine enough to get the water inlet valve free. Didn't have to remove the bolts at the bottom of ... Read more the back of the machine (they were pretty rusty) Just removed the single screw holding the water inlet valve in place, slid it down and away from the back cover and could fish it out to the side and disconnect the hose (with plyers) and slide off electrical clips (make a note of which clip goes to which valve.) I removed the part first so I could make sure I was ordering the right one. When the part came (very promptly by the way) it went back together easy. Only question was regarding reinstalling the wires since I didn't mark which way they went. I knew which one went on the Hot and Cold but didn't know if it mattered which clips went on each terminal. Figuring it was AC guessed it didn't matter so put it together the way the connectors seemed to want to lie naturally. Put it together making sure no hoses or wires where pinched or rubbing against sharp edges. Replaced the rubber washers in the hoses and made sure the hose connectors turned freely (they had been rusted a bit and didn't turn on the hose freely and I think this was the start of the cross threading problem) This time the hoses went back on very easily, screwed them hand tight not forcing anything at any time (DIDN"T USE PLIERS!). Tried water and no more leaks. Washer filled faster also, think this was because the screens on the water valve were plugged. I'll have to remember to take the hoses off and make sure the screens are clear every couple years or so. If you are having slow fills, suggest you check this first before tearing in to the machine.

placed washer on side and installed new pads
and returned washer upright

Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive ass ... Read more embly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and starte ... Read more d stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.

Basically I followed the great instructions provided on the Part Select webpages. I would consider myself to have more common sense than mechanical skill. I didn't want to have to keep going back to purchase more parts so I decided to buy the motor coupler (under $5), new clutch assembly (Under $30), new motor (under $160). The shaft o ... Read more n the original motor wore down to a cylindrical shape which should have been more of a rectangular shape to fit precisely into the motor coupler and provide the grip strength for the washer tub to spin. Usually the no spin problem is linked to a faulty motor coupler. I was glad that I had to removed the motor to reach the motor coupler because in my case the coupler had not failed. That is when I saw the motor shaft had worn. Since I had all the new parts I replaced them all and since 6/13/19 the washer is running like new. Oh, the problem was most likely caused by someone in my family "overloading" the wash machine one too many times over 11 years. Guy's / Gal's you can do this and save yourself from buying a new washer for between $850 - $1,200. My repair expense was under $240 including tax and next day delivery of my parts. Thanks Part Select !!!! Neil

3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the ... Read more suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.