KAWE550VWH0 KitchenAid Washer - Instructions

Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.

We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing complet ... Read more ely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.

Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new ho ... Read more se onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spr ... Read more ing bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!

I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the ... Read more hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.

Pulled up on fabric softener dispenser and removed it. Had to use pliers to remove cap and seal to get access to the bolt holding the agitator in.

Realized my socket extension wasn’t long enough so went to Lowe’s and bought another.

Was unable to hold the bottom of the agitator to keep it still and get enough lever ... Read more age to remove the bolt. I poured hot water over it and then climbed into the washer and used my foot to hold the vanes still while I removed the bolt. Once I got the agitator out, the rest was a breeze. Separated the top of the agitator from the bottom by placing it on the floor, using my feet to hold it down and pulling up to remove the top part of the agitator.
Turned the top of the agitator upside down and removed the cam and feed dogs. Assembled the new one and held the agitator top horizontally while placing the new part back in.
Reassembled the top and bottom of the agitator and put it back into the washer. Tightened the bolt, replaced the cap with its seal and pressed the fabric softener dispenser back into place.

Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished

just like video showed really helpfull

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy rep ... Read more air.

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!

the first order was ordered wrong for me and the part was to big so I had to send it back and order another. The second dispenser was the right one and went on well to the machine. Just had to put it on the machine by hand.