KA108 Maytag Washer - Instructions

I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.

Tilt washer. Remove old belts. Put in new. Tighten transmission bet and pump belt per YouTube. It works like new now.

Shut off the electricity (pulled thee plug). Working from the rear of the washer. Removed water hoses with Stillson wrench. Removed two self tapping screws with nut driver to get to the assembly. Slipped off the wires lugs one at a time from thee old assembly and slipped them onto the new valve assembly in the same location. Installed the ... Read more new assembly. Attached the water hoses to the new inlet valves. Note: My washer had the hot and cold valves identified on the washer. The replacement valve assembly was marked hot and cold (H, C.). which was the reverse of the marking on the washing machine. Go by the marking on the washing machine.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. ... Read more I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

1. Removed hoses 2. Removed inlet valve. 3. Took valve apart to discover defect in diaphram. 4. Looked up and ordered part. 5. Replaced inlet valve. 6. Tested washer.

I followed steps outlined on you web page.

Followed web instructions.

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .

When the part came in, it was just a matter of getting the old part out, and replacing it! Incredibly smooth---the hold down screws were obvious, so once I got them out---the part came out of the machine, I disconnected the two control wires, reconnected them to the new part---and reinstalled!

Part shipping was great got here in two days-

I pulled off Front panel (two screws) and lifted Top panel (2 screws) and disconnected the inlet hoses. I removed the old Inlet valve. (1 scew and valve to tub hose connection).

Before Installing the new valve, i shifted the connector positions on the selenoids to match ... Read more the old valve. and installed by reversing the steps. All went very smooth. Thanks, It was easy.

Simple removal of the mounting plate holding the old valve to the rear of the machine followed by disconnection of the water hose to the washer from the valve and unplugging of four electrical connections. Reattached the new valve to the water hose and then reattached the new valve to the mounting plate, finally reconnecting the wiring co ... Read more nnections (4). Installation completed by reattaching the valve mounting plate to the washer. The diagnosis was confirmed by blowing into the old valve's water inlet. Air would pass through the valve, confirming that it did leak when the valve was closed. Air blown through the new valve prior to installation would not pass through the new valve.

Tilt the washer sideways. Remove belts,Remove front panel, loosen two hoses, loosen three small nuts. Take out old pump and install new new pump vise versa. Video provided by partselect very helpful.

Change the position of electrical connection on inlet valve before installation to match positions of old valve. Shut off electricy and water to washer. Disconnected water hoses, and power wires to old valve. Removed old valve and installed new valve exactly as installed on old valve. Washer operated perfectively

Removed 2 screws on the bottom of the front of the washer and pried the front off. Then removed 2 more screws for the top of washer and rocked it back to expose the water inlet vavle. Removed the water inlvet vavle and replaced it. Then put it all back together. Done

I first shut off the cold and hot water hoses so that no water would run while replacing the part. After that I made sure to unplug the washer .Then I removed the plate that was holding the water inlet valve with a 1/2 " nut driver ,I think there were four bolts .Then I removed two more bolts from the center of the plate that were holding ... Read more the water inlet valve.I then disconnected one 1/4 " screw or I should say loosened one which held the main water hose going into the washer which then released the part ,except from four wires. I then took one wire off at a time and attached to the new part one at a time.Finally, I was finished and reconnected everything .It worked perfected !I'am very happy and pleased . This washer is over 25 years old and still runs .