This light bulb is located on the inside of your microwave. The bulb is behind the top grill. It will need to be replaced when it has burnt out and no longer works. Unplug the unit before beginning this repair. Remove the top grill of your microwave, use your screwdriver to open the light socket, scrape off any silicone holding the bulb i...Read moren place, clean the area of any oil and dirt, insert the new bulb into the socket without touching the bulb, slide the holder back into place, line up the tabs on top of the metal plate, and secure the holder back into place.
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the microwave becomes unresponsive, the microwave produces little to no heat, or the appliance simply does not turn on, it could mean that your fuse ...Read moreis at fault and needs to be replaced. Because this part contains an electrical charge, remember to disconnect power to the microwave unit before you begin this repair.
NOTE: Before you start this repair, ensure that the microwave is unplugged, and the capacitor is discharged. A capacitor stores large amounts of electricity even after your microwave is unplugged.
The grease filter can be found on the bottom of the microwave. If your grease filter is damaged, it will not effectively capture grease that builds up when your microwave is in use. To replace the grease filter, simply grasp the filter ring and push it to the back of the microwave, then lift out the filter. To preserve the life of your gr...Read moreease filter, you should occasionally remove them and gently wash them in a warm water and detergent solution. Most microwaves will have two grease filters, but this part is sold individually. The grease filter is approximately 8.5 inches by 5 inches.
The rotating ring in your microwave rests under the microwave plate, and allows it to rotate when the microwave is running. It is a round plastic ring with 3 wheels spaced out around the perimeter. If your microwave plate or tray is not turning, you could have a broken or damaged rotating ring. This plastic ring is gray in color and is ap...Read moreproximately 10 inches in diameter. The 3 wheels are made of white plastic. This part is sold individually.
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs airflow through the vent duct. The main reason you would replace the damper bracket is if it is damaged and will not hold the damper in place p...Read moreroperly. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed to hold it in place. You will need a screwdriver in order to secure the mounting bracket into place. Part has been substituted. Part is no lo...Read morenger a U-shaped bracket, it is now a flat mounting plate and will function the same.
This switch monitor interlock is a critical safety component designed to ensure proper communication between the microwave door latch and the control board. When functioning correctly, it confirms that the door is securely closed before allowing the microwave to operate. A damaged or faulty switch may prevent the unit from starting, even ...Read moreif the door appears latched. Replacing this genuine part restores safe and reliable operation. Installation should be performed with care, and it's recommended to disconnect power before beginning any repair.
This vent damper is a manufacturer-approved replacement part for your above-range microwave. This part helps vent air from the microwave to the exterior of your home, and helps keep exterior wind out of the vent. Replacing the vent damper will require some disassembly of your microwave/ Unplug the unit before beginning work on it.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David - For model number JVM1790WK01
December 10, 2019
How can i order a vent fan cover
Hello David, thank you for your question. The replacement grille for this unit is Part #: PS1020747. Please enter the part number into the site for current price and availability. Good luck with your repair!
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Jim - For model number JVM1790WK01
January 28, 2020
This model has two lights one under the unit (night light) and one inside the unit. I cannot find instructions for replacing the inside light.
Hello Jim, Thank you for the question. Here is a link to a How to Video that may help. Good luck with the repair.
https://www.youtube.com/watch?v=-yUtoBg17Jg
the exterior plastic ventilation cover is broken, I tried to glue together no luck - Is there a replacement part I can buy ?
Hi Ronnie, thank you for your question! The vent grille for your model is part number PS1020747. Please reach out to customer service if you need help placing an order!
Everything seems to be working except it does not heat up, can this be repaired? Thank you.
Hello Raymond, Thank you for the question. For safety reasons, since the microwave capacitor can still store electricity even when the microwave is unplugged, it is usually advised that you discharge the capacitor before any attempt at repair. We have included a link on how to do so. There are two parts we suggest testing. First we suggest checking the Diode, It should read around 50K Ohms. You can also check the Magnetron. The magnetron can be tested with an multi meter set on the highest scale. Across the terminals, you should read 0 ohms (or .5 ohms). Test both terminals to ground with one lead and make sure it is not shorted. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave completely stopped working
968 of 1266 peoplefound this instruction helpful.
Kim from Cliffside Park, NJ
Really Easy
15 - 30 mins
Screw drivers
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic
... Read morerowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Was this helpful?
Thank you for voting!
Under the vent light bulbs needed to be replaced
66 of 87 peoplefound this instruction helpful.
Robert from Naples, ME
Really Easy
Less than 15 mins
Screw drivers
Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!
Was this helpful?
Thank you for voting!
Loss of Rack holder clip for GE Profile Convection Microwave oven
35 of 47 peoplefound this instruction helpful.
Nancy E from Cincinnati, OH
Really Easy
Less than 15 mins
It was super easy! Opened the door, matched up the hole on the side of the microwave convection oven with the first portion of the rack holder clip, pushed in the rack holder clip and made a twist to ensure the rack holder clip seated in the wall of the oven. Less than 30 seconds to install - no tools necessary. I that the clips came
... Read morein an order of a unit of 8 clips, allowing me a quick-fix if I need additional clips for loss. Now I have stable racks within my oven ensuring safe insertion and removal of food from the oven. Having the full use of both of the racks in my convection oven during the summer is a Godsend, especially living in the Ohio Valley with its' hot steamy summers - my kitchen stays cool as a cucumber, and so do I!
My Orders
