JT980BHB General Electric Range - Instructions

Replaced High Voltage Diode. Very carfully due to the extream danger of a electrical shock.

Attatched trim bracket to cabniet with screws that by the way were not supplied then attached plastic trim to bracket

Followed instructions and removed door. Loosened screws/bolts. Pulled the door apart. Removed the bracket that would hold the glass. Removed the broken glass and inserted the replacement glass. Re-assembled the door and reinstalled the door. Took all of 20 mins.

Most important: Unplug or turn off the breaker before beginning! (I briefly saw sparks as I removed the old switch.) Look at the replacement switch. The springs on the sides hold the switch in, which means you have to press in these springs to get the old switch out. I slipped a small screwdriver in on the side while I pulled with a s ... Read more mall pair of pliers. It's tricky, but it will come out. Once you have the switch out, just unplug the wire in the back, making sure it doesn't fall back in the hole before you get the new switch on. Then, just push the new switch into the hole in the stove and you're done.

Ordered window pack from PartSelect then removed oven door from front of stove, then removed back of door and silver backing and glass pack. Dropped new glass into place. Replaced all backing,put door back onto stove. Tip. When removing screw keep them separated from each other as not to get mixed up when putting everything together. Goo ... Read more d Luck, PartSelect has all the parts you need, this my second getting a part from them.

It wasn’t the magnetron.
It wasn’t the diode.
It wasn’t just the fuse.
It was the High Voltage Capacitor (HVC). You know, the very thing they warn you about when opening the microwave. Just remember to discharge it using needle-nose pliers before probing around to find the problem. I also suggest you invest in a multimeter ... Read more so as not to waste hundreds of dollars like I did; that way you can go straight to the real problem instead of replacing symptoms. If you replace the HVC, you will also want to replace the two fuses right in front of it. Also, there is a wiring diagram and a troubleshooting flowchart tucked behind the front console near the top. It is extremely useful!

Wait until oven is cold. Turn off power to the oven at the breaker panel (confirm: clock will be off). Open oven door. Remove upper rack. Unscrew glass cover over lamp and socket (it only turns one direction and may be tight). Slide cover off lamp socket. Remove old lamp - pull straight down. Install replacement lamp. Lamp pins line up fr ... Read more ont to back. Do not touch the lamp - use latex gloves. Make sure the lamp is fully pushed into its socket. Replace the glass cover by centering it on the socket with glass retaining tabs close to the matching areas on the metal socket. Take care not to damage the lamp. Turn the cover to lock in place. Make sure it is locked. Replace oven rack. Turn the power back on.

must of had loose connection from wire terminal
to thermostat from factory. thermostat and wires
were melted. removed thermostat. and cut burnt
wires back. replaced thermostat and terminals.
used better quality terminals than factory.
also checked and tightened other loose connections. there was enough wire left ... Read more after cut back to just put on new terminals.

Just pulled out the old one and pushed in the new one. Very easy. I was afraid to run this self-cleaning oven until I installed the new gasket. It worked perfectly.

Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.

Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.

Watched video

turned off power to oven; pulled out old bulb (unscrewed glass cover to access). Noted the direction of the electrical prongs when pulled bulb out... and inserted new bulb. Turned back on power to oven - bulb worked

I'm well past ninety and my sweet daughter inserted the tiny prongs. I was delighted to find a place that had the bulbs. Thank goodness for the internet ! (I'm not too old for that)

took bulb out, but new one in lol