JSP47CF6CC General Electric Range - Instructions

First and foremost, I am a 63 year old cooky baking GRANDMOTHER. I don't know anything about fixing appliances. I read the other repair stories pertaining to my burner and I thought, "why not."
It was a snap!

My part arrived the very next day, bless you Parts Select! I just did what the others (see above) did: I remov ... Read more ed 2 screws to release the stove top, then I took a few digital photos to be sure I would know where the wires went. I released the old burner, pulled out the thingamajigs that held the wires in the old burner, then pushed the new ones in their place, replaced the stove top, plugged it back in, turned it on and jumped for joy! If I can do this, anyone can.

The burner would work but you could not regulate the heat. I ordered and replaced the control switch for that burner. The part was like for like and reasonably priced compared to other websites and dealer. The picture showed that it was identical. I ordered one day and it was here the next. I had drawn a diagram of where the wires went on ... Read more the old switch so it was very easy to replace. Probably took me 15 minutes or so. Works perfectly and by buying from this website it saved me a few bucks.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

After reviewing the potential causes for the error code, I decided I'd try to change out the temp sensor. Using the ohmeter, I saw the difference immediately between the old and new sensor. The sensor is accessed from the back of the stove, and must be slide out to gain access to the rear panel. Since the stove I have is a built in, re ... Read more moving the stove and the access panel was the hardest part of this repair. Resetting the glass control panel was also a bit tricky to calibrate the touch sensitive buttons. Good luck.

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

The hardest part was getting the correct part. I trusted the on line number and the first part I received was incorrect. I should have taken the part number off the old switch. When I did, I found out that the part number changed when I tried to order it. When the part came, the wiring instructions were not even close. I just took one wir ... Read more e at a time off the old switch and put it on the same terminal of the new switch. The repair was/is very simple made complex and too much time because of a wrong part and incorrect wiring instructions. As far as getting the incorrect and correct parts through the mail it was very fast. Received both parts in less than 3 days. A bonus is that I sent the old switch back for a rebate. Thanks for that.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Basically removed the screws holding the op on and removed the vent from back. Just "figured it out" and now it works. Wish I could be more helpful. Recommend moderate experience and confidence.

Looked up the part, ordered it, and it was there in 3 days. It was slightly different than the old control, but a very well-written set of instuctions detailed which wires to move to which terminal. The entire repair took about 30 minutes, including moving the range out, replacing the control, and push the range back in place. Works pe ... Read more rfectly.

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary scr ... Read more ew, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Disconnected breaker. Removed knobs, plastic retaining nuts mounted to each switch shaft. Removed four 1/4 inch hex head screws on front panel and two screws securing defective switch. Removed bad switch, and replaced with new part. Took photo of wiring before removing old part. Referred to photo to ensure correct wiring of new part. Reas ... Read more sembled front panel in reverse order of disassembly. Turned breaker to on, and tested new switch. All worked well.

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.