My Orders
- Home
- JS968TF2WW
- Instructions
JS968TF2WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The small burner inside the double burner shortd out.
5 of 5 people
found this instruction helpful.
-
david from PORT ORANGE, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
Right front burner had no heat control. (High heat when on "Low")
7 of 11 people
found this instruction helpful.
-
John from Ocoee, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Pull range out of the "hole", and spin so that back of range is accessible. Remove cover over top "control area" on back of range. (Four screws that happen to be the same size as the magnetic socket that holds the interchangeable tip on a cordless screw gun. Simply remove this tip, and use the tip holder as a magnetic nut driver!). Rem
... Read more
ove the knob by pulling gently straight off. Remove black plastic retaining nut under where knob was. Inside are two small screws that hold the switch in place. Remove these screws with a magnetic screwdriver (If you drop these screws and lose them, you'll have a hard time finding them. Very small!!). Carefully follow enclosed instructions to move the wires from the old switch to the new switch. Put back together in reverse order.
Read less
Was this helpful?
Thank you for voting!
Broiler Element Failed
6 of 8 people
found this instruction helpful.
-
Ron from Irvine, CA
- Really Easy
- 15 - 30 mins
-
Socket set
Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mo
... Read more
unting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.
Read less
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 people
found this instruction helpful.
-
Barry from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
the temp was not accurate
7 of 12 people
found this instruction helpful.
-
scott from new harmony, UT
- A Bit Difficult
- 15 - 30 mins
-
Socket set
had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yu
... Read more
m.
Read less
Was this helpful?
Thank you for voting!
oven not as hot as temp display said it was
4 of 4 people
found this instruction helpful.
-
John from HOT SPRINGS, AR
- Really Easy
- 30 - 60 mins
-
Nutdriver
pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.
Was this helpful?
Thank you for voting!
Oven slow to heat.
6 of 10 people
found this instruction helpful.
-
Scott from Burleson, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.
Was this helpful?
Thank you for voting!
Melted Plastic and use of water caused false bottom to be damaged badly
5 of 7 people
found this instruction helpful.
-
Michael from Wildwood, MO
- Really Easy
- Less than 15 mins
Oven door must be removed briefly while old false bottom is slid out and replaced with new one. Oven door is easily replaced and oven is like new.
Was this helpful?
Thank you for voting!
One of the drawer supports broke off
5 of 7 people
found this instruction helpful.
-
John from Sandy Hook, CT
- Really Easy
- Less than 15 mins
-
Nutdriver
I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it com
... Read more
plete.
Read less
Was this helpful?
Thank you for voting!
Burnt Broiler Element
5 of 7 people
found this instruction helpful.
-
ROBERT P. from Santa Fe,, NM
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy
... Read more
to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!
Read less
Was this helpful?
Thank you for voting!
outside element burned out
4 of 4 people
found this instruction helpful.
-
peter from westfield, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs.
plugged in the new element and screwed it in place
plugged in the new element and screwed it in place
Was this helpful?
Thank you for voting!
bulb burnt out
5 of 7 people
found this instruction helpful.
-
Christie from NAPERVILLE, IL
- Very Easy
- Less than 15 mins
turned off power to oven; pulled out old bulb (unscrewed glass cover to access). Noted the direction of the electrical prongs when pulled bulb out... and inserted new bulb. Turned back on power to oven - bulb worked
Was this helpful?
Thank you for voting!
Oven light
4 of 5 people
found this instruction helpful.
-
Letty from KERRVILLE, TX
- Very Easy
- Less than 15 mins
I'm well past ninety and my sweet daughter inserted the tiny prongs. I was delighted to find a place that had the bulbs. Thank goodness for the internet ! (I'm not too old for that)
Was this helpful?
Thank you for voting!
The front right outer element was defective.
4 of 5 people
found this instruction helpful.
-
Peter from Abbeville, LA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
My cooktop is a stand alone unit mounted in a counter top not associated with an oven.
-Removed power to the cook top. Breaker off.
-Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. T ... Read more his is a two person job preferably.
-Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back.
-Remove knobs and remove the glass top by lifting straight up.
-Record the wire positions on the element on paper and remove the connections.
-The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose.
-The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this.
-Placed the new element in position and reinstalled the spring clips.
-Install the wiring terminals in the correct positions.
-Reinstalled the glass surface and the six phillips screws. Reinstall the knobs.
-Lower the cook top back into its counter top position.
-Return power to the cook top.
-Installation complete. Very simple!
-Removed power to the cook top. Breaker off.
-Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. T ... Read more his is a two person job preferably.
-Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back.
-Remove knobs and remove the glass top by lifting straight up.
-Record the wire positions on the element on paper and remove the connections.
-The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose.
-The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this.
-Placed the new element in position and reinstalled the spring clips.
-Install the wiring terminals in the correct positions.
-Reinstalled the glass surface and the six phillips screws. Reinstall the knobs.
-Lower the cook top back into its counter top position.
-Return power to the cook top.
-Installation complete. Very simple!
Read less
Was this helpful?
Thank you for voting!
Broker inner glass
4 of 5 people
found this instruction helpful.
-
marc from PARK RIDGE, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Very easy to remove the parts and to reassemble
Was this helpful?
Thank you for voting!