My Orders
- Home
- JS960TB1WW
- Instructions
JS960TB1WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not cook over 325 degrees and sometimes would burn your food.
15 of 19 people
found this instruction helpful.
-
phil from forney, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed the unit from the wall,removed the back panel to access the wires to the sensor,cut the plug off of the new sensor and strip the wires back,used the wire nuts to attach the new sensor,put all back together and slid back into the wall and works excellent.
Was this helpful?
Thank you for voting!
Oven not heating
14 of 21 people
found this instruction helpful.
-
Joseph from Stuart, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.
Was this helpful?
Thank you for voting!
RF Dual Burner out. Smoke in the area of controls
12 of 15 people
found this instruction helpful.
-
Al from Ocala, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Shut off circuit breaker. Removed cooktop from island counter. Removed all knobs. Removed all screws after finding layout diagrams of unit on your web site. Lifted glass top from metal cabinet. Ordered control after trouble shooting the problem. (Master Electrician). Obviously burned out from water in control. Ordered control on line and
... Read more
installed it when it arrived three days later. Before installing control I cleaned and dried out the area. I cleaned the glass top around all the control shaft holes and the rubber boots and lubricated them with silicone to help keep them dry and for ease of turning controls. Turned on circuit breaker and checked all burners, pilot light and hot top indicating lights.
Read less
Was this helpful?
Thank you for voting!
Dual burners stay on hi all the time. No regulation.
11 of 13 people
found this instruction helpful.
-
Peter from whitesboro, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The hardest part was getting the correct part. I trusted the on line number and the first part I received was incorrect. I should have taken the part number off the old switch. When I did, I found out that the part number changed when I tried to order it. When the part came, the wiring instructions were not even close. I just took one wir
... Read more
e at a time off the old switch and put it on the same terminal of the new switch. The repair was/is very simple made complex and too much time because of a wrong part and incorrect wiring instructions. As far as getting the incorrect and correct parts through the mail it was very fast. Received both parts in less than 3 days. A bonus is that I sent the old switch back for a rebate. Thanks for that.
Read less
Was this helpful?
Thank you for voting!
Oven would not maintain set temperature
11 of 16 people
found this instruction helpful.
-
Leonel from Biddeford, ME
- Easy
- 30 - 60 mins
-
Screw drivers
No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140
Was this helpful?
Thank you for voting!
The burner light was on - burner control spun freely
11 of 19 people
found this instruction helpful.
-
Richard from Indianapolis, IN
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Looked up the part, ordered it, and it was there in 3 days. It was slightly different than the old control, but a very well-written set of instuctions detailed which wires to move to which terminal. The entire repair took about 30 minutes, including moving the range out, replacing the control, and push the range back in place. Works pe
... Read more
rfectly.
Read less
Was this helpful?
Thank you for voting!
Rotary switch for the dual control burner failed
8 of 11 people
found this instruction helpful.
-
Robert from Belvidere, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed range from cabinets then approximately 6 sheet metal screws from the front of the range and two 1/4" sheet metal screws from the side to remove the front and top of the range. Lifted the cook top removed the two screws from the rotary switch and followed the directions included with switch to connect the wires. In reverse order
... Read more
reassembeled the range.
Quick & Easy
Quick & Easy
Read less
Was this helpful?
Thank you for voting!
Oven light did not work
9 of 16 people
found this instruction helpful.
-
Howard from Rio Vista, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 people
found this instruction helpful.
-
Barry from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
5 of 5 people
found this instruction helpful.
-
Richard from CUMMING, GA
- Really Easy
- 15 - 30 mins
-
Socket set
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
Was this helpful?
Thank you for voting!
Right front burner had no heat control. (High heat when on "Low")
7 of 11 people
found this instruction helpful.
-
John from Ocoee, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Pull range out of the "hole", and spin so that back of range is accessible. Remove cover over top "control area" on back of range. (Four screws that happen to be the same size as the magnetic socket that holds the interchangeable tip on a cordless screw gun. Simply remove this tip, and use the tip holder as a magnetic nut driver!). Rem
... Read more
ove the knob by pulling gently straight off. Remove black plastic retaining nut under where knob was. Inside are two small screws that hold the switch in place. Remove these screws with a magnetic screwdriver (If you drop these screws and lose them, you'll have a hard time finding them. Very small!!). Carefully follow enclosed instructions to move the wires from the old switch to the new switch. Put back together in reverse order.
Read less
Was this helpful?
Thank you for voting!
The small burner inside the double burner shortd out.
5 of 5 people
found this instruction helpful.
-
david from PORT ORANGE, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
wire connection to socket was bad
6 of 10 people
found this instruction helpful.
-
David from Gansevoort, NY
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Was this helpful?
Thank you for voting!
outside element burned out
4 of 4 people
found this instruction helpful.
-
peter from westfield, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs.
plugged in the new element and screwed it in place
plugged in the new element and screwed it in place
Was this helpful?
Thank you for voting!
Burner element was burnt
4 of 5 people
found this instruction helpful.
-
Chandra from Naugaeuck, CT
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
It was very easy. First turn off the power. Remove two screws to pick up the hood then remove two screws holding the element. Tag the wires with number. Unplug the old burner attach the wires to new burner. Attach two screws with spring to hold the burner, put the hood down and put the screws holding the top hood.
Was this helpful?
Thank you for voting!