JS750SF1SS General Electric Wall Oven - Instructions

I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wal ... Read more l. Overall, a very easy repair once you get the oven out.

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U ... Read more nscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.

Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and scre ... Read more wed back in place. Reinstalled oven door. Tested temperature settings by turning on oven and comparing with a separate oven thermometer.

After reviewing the potential causes for the error code, I decided I'd try to change out the temp sensor. Using the ohmeter, I saw the difference immediately between the old and new sensor. The sensor is accessed from the back of the stove, and must be slide out to gain access to the rear panel. Since the stove I have is a built in, re ... Read more moving the stove and the access panel was the hardest part of this repair. Resetting the glass control panel was also a bit tricky to calibrate the touch sensitive buttons. Good luck.

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

Took off the knobs and retainer nuts. Carefully setting them on top in the same order as they came off. Unscrewed the bottom retainer screws. Removed the main control trim. Unscrewed the top retainer screws. Carefully pulled the broken control assembly panel out of the wire harness. Reversed the procedure to install the new Panel. ... Read more
Found the part quick and easily on your site and had it shipped next day. Wonderful Experience!

Pull the old one put in the new one ... took about 20 minutes

lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it

Disconnected breaker. Removed knobs, plastic retaining nuts mounted to each switch shaft. Removed four 1/4 inch hex head screws on front panel and two screws securing defective switch. Removed bad switch, and replaced with new part. Took photo of wiring before removing old part. Referred to photo to ensure correct wiring of new part. Reas ... Read more sembled front panel in reverse order of disassembly. Turned breaker to on, and tested new switch. All worked well.

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary scr ... Read more ew, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Removed panel to gain access, removed wires from switch from burner that was not operating and attached them to switch for burner that was working. Burner worked, problem identified. Replaced bad switch with new switch. Problem solved.

Cut all power to the range. Easy to remove front panel and then screws and nuts that hold both white frame and glass top to range. Once the top can be lifted, cut the plastic zip tie that retains the harness. Unplug the harness and then remove the top. make provision for new zip tie before
the range top is re-installed. The range ... Read more top is to be inverted for installing clips to the new heating element. Make sure that the holes line up to the pointed clips that hold the element. Not required to move the range.

This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.

- remove door from range following the basic guide to removing any range door.
- place door on work surface with the outside facing down.
... Read more - remove three 1/4 socket screws from bottom and two star screws on top.
- Flip door over, remove outer door panel and set aside.
- There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside.
- Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed.
- Remove the remaining 1/4 screws holding the aluminum shielding.
- Remove the shielding being careful not to disturb the insulation around the window.
- Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom)
- Set the new window in its place.
- Reverse the process by replacing the aluminum shield, hinges, than internal glass pane.
- Set outer door on top and holding everything together, flip door.
- Tighten the two star screws on top and the three 1/4 socket screws on the bottom.
- Replace door. Don't forget to lift up those hinge tabs before trying to close the door.
All done. Pat yourself on the back for a job well done.