JR19*07 General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, reconnected the wires to the new element, reattached it to the oven and voila!

It worked. What was really cool, once I ordered the part, I received it in only two work days!

Goo ... Read more d job folks!

Hardest part was getting the wrong element and having to send it back and reordering correct one....too many variables. Two screws inside the oven removed, pull out range and take off back and attach new element to plug ins!

Successful repair to Our GE range, manufactured prior to 1965 (when installed in house). Pulled range from wall, unplugged, removed burned-out broiler element. Previous check with GE to make cross reference of range part number to Part-select part number for this nearly 50-year-old range. Obtained new part and installed. Works. Range has ... Read more self-cleaning oven, accidentally destroyed thermal switch attached to element mounting bracket, difficulty with frozen mounting nut. Self-cleaning still works; thermal switch locks out a solenoid which defeats door latch; prevents premature opening of oven door when oven too hot to open safely. Internet search did not find GE part but there are generic devices of the same type available; will consider installation later.

Turned off power at breaker panel. Removed 2 screws attaching element to stove. Pulled element out a couple of inches and removed 2 wires attached with screws. Installation is reverse order of removal.
Be careful not to twist the terminal ends when tightening screws.

shipping was very fast!

Of course I unplugged the stove. Then I removed the cover to reveal the connections for the element. After unscrewing the two wire connectors, I had to use a nut driver to remove the two screws holding it in place in the oven. The new element went in easily. I screwed it in place in the oven and then attached the two wires in the back ... Read more and replaced cover. Plugged it in, tested it, and we were good to go.

Note: this was a second attempt, The first time I ordered a heating element with push on connectors not screw on. Beware! Pay attention to the pictures and description. I ordered too quickly.

First I removed the two screws in the back. then I removed the two screws attached to the brace at the top. pulled the old element out. Removed the screws that attatced the wires to the element. Attached the wires to the new element. Pushed the wires back in. Pushed the element in and attached the screws. Reattached the support. Turned on ... Read more the broiler. The element smoked for a few seconds before getting red hot. It is working fine.

Pull the stove out from the wall and unplug. Had to remove back of stove, the aluminum sheilding and the duct work to get at wires use nut driver. Then used nut driver to remove nuts from broiler unit inside stove. Take the front overn dover off first. The new part did not match up with the wires so I used a needle nose to spread the wi ... Read more re clips just a tad so they would fit over the tabs of the broiler unit. Do all of this behind the stove as you do not have eough wire to do this effectively from the oven side. After I had the tabs fitted to the broiler unit. I removed them and fed wires back through the stove. I then went back to the front of the stove and put the broiler back in and put support bar back in to ceiling of stove and the two nuts back on to affix broiler to back of oven. Put the aluminum baccking and duct work back onto the back of the stove and plugged it back in. Pretty easy job.

Our element blew in our oven, we took it out and saw what we needed. It was very easy to see what part we needed to order because of the great pictures on the website. The larger views really helped. We got the part quickly and put it in. It was a breeze and now our oven is working great! The best part however, is it only cost about ... Read more $33.00 including shipping and handling. Much cheaper than if we would have had someone come in to fix it!

Turned off power at panellboard. Disconnected mounting hardware from inside oven chamber. Pulled failed heating element with wires attached into the oven chamber. Disconnected wiring and reconnected them to the new heating element. Tightened screws while holding connectors with pliers. Applied electrical tape to connections. Pushed wires ... Read more back into opening and secured heating element back into place. Restored power nad verifed proper operation. The other heater purchased will be used when the bake element finally fails,

(1) Turned off power source.
(2) Removed rust on screw heads before attempting to loosening them up.
(3) Pulled the element out to expose the connections.
(4) Disconnected with phillips screw driver, taped off wires to prevent mixed-up during re-installation.
(5) Re-installed new element using new screws provided.

First, shut off the breaker to the stove. Removed old element by unscrewing the two screws on the plate where the element attached at the bottom of the inside of the oven. The old element was corroded at the connection, so disconnect it, attached the new one, pushed it back in the insulated socket then reattached the two screws on the pla ... Read more te. Flipped the breaker back on. Works great. Only took about 25 min. from start to finish.

Note: Please make sure power is off!!! Turn off at the fuse panel,Main. Test oven after you turn off breaker...try turning on oven with normal switch, indicator light should be off. Also check interior light, usually wired 110 volts, may be on a separate circuit, just for safety!!. Remove retaing screws, scewdriver will work , but a nut d ... Read more river is easier. Pull old element out gently and check between terminals with volt meter. Remove screws on element holding feed wire, reverse this process to install. Test oven for proper operation after installation...make sure oven cycles through a set temperature range.

turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.

Simple repair that was complicated by not being able to remove the oven door, leaving a long reach to the element connections in the back of the oven. Other than the accessibility issue, the repair is easy. Remove two scews, pull the element out about 3 inches to access and unscrew the screws holding the wires to the element. Then reve ... Read more rse the process with the new element. But, because of the long reach, there were alot of dropped screws and cussing.

Before you start, make sure the circuit breaker is not tripped, which can explain element not heating.
In my case, the toaster element was ok, which tells us that the oven is receiveing electric current.
1) Take the grills out so you have free access
2) Remove the door - this model just pull it up to let it free
3) rem ... Read more ove the 2 screws securing the element on backwall of the oven and gently pull the element out
4) if you have a multimeter:
a) set it to AC, greater than 300 V
b) use your alligator clips, attach the clips
to the contacts of the element
c) briefly turn the oven on: expect to read between 230 and 260 volts
5) remove the screws securing the old element
6) install the new element;
7) secure the element back to the backwall
8) turn the oven briefly on and feel the heating element: should come warm pretty quic;
- Job done -

When you remove the screws securing the wire to the old element, make sure the wires are not cracked, or interrupted.

Otherwise, a real simple and easy fix.

Specs of this element are what I missed but here they are:
Resitence : 25.5 Ohms
Volts: 230 - 260Volst
Power : 2050 to 2650 Watts
The power depends on the voltage, so make sure you dont have it too low (less than 220 ) or too much (yeah, 260V is nearing upper limits)