JN3201 Makita Nibbler & Shears - Parts

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This tapping screw is an authentic hardware that is supplied by original tool manufacturer for use with a variety of Makita power tools. It has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. Note this durable metal screw is sold individually.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a Genuine OEM replacement part used on Makita Power Tools. This item is made out of Plastic and it is Sold Individually. The purpose of the Brush Cap is to retain the Brushes in the Brush Holders. This Brush Cap has external threads that thread into the housing of the tool. Be careful when removing and replacing these, they have a tendency to break.

This set of two carbon brushes is a genuine Makita replacement part, packaged in an official Makita retail box. Each brush includes wire leads and attached brush springs, and is designed to restore optimal performance in compatible Makita tools. Carbon brushes are among the most commonly replaced components in power tools, as they gradual...Read morely wear down through friction and regular use. Worn brushes can lead to intermittent motor function, reduced power, or diminished electric braking. Replacing them can resolve these issues and restore proper motor performance. Signs of wear include brushes worn near the wire lead, or those that are cracked, pitted, or burned. When replacing carbon brushes, it’s also important to inspect the armature for any signs of damage, such as burns or cracks, which may indicate a more serious motor issue.

• This cord guard is a genuine Makita replacement part and is sold individually. • Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. ...Read more • This cord guard will fit cords for the tools listed under the "Compatible Tools" listing. It is not guaranteed to fit any other cords.

This is an OEM replacement part used with Makita sanders/routers. This switch is what allows user to turn the unit on and off. It is plastic a plastic switch with metal terminals. Over time mechanical moving components of a switch will begin to fail requiring a replacement. Please note this item is sold individually. To complete this rep...Read moreair you will need a screwdriver. • Remove housing • Disconnect wires • Remove old switch • Install new switch • Re-attach wires • Reassemble and test the unit

This genuine OEM woodruff key is a small, semicircular metal piece used in various power tools to connect rotating parts, such as shafts or gears, to other components like wheels or pulleys. It prevents slippage between these parts, ensuring smooth synchronization and power transmission. With a width of 3/32 inches and a length of 5/8 inc...Read morehes, consider replacing a woodruff key if you notice misalignment or excessive movement between the connected parts. Be sure to inspect the key for signs of wear, damage, or bending. Removing the key depends on the make and model of your tool. If the key is visible, gently tap it from one side using a small hammer and a punch or drift pin. This will dislodge it from its slot. If the key is stuck or difficult to access, you may need to partially disassemble the tool to gain better access to the key. Once the key is loose, carefully pull it out using pliers. Clean the keyway and slot before installing the new key. Before making your purchase, remember that this component is sold individually.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

Included in Part Number 539168-0

Included in part number 596141-3