- Home
- JMS08BA2WH
- Instructions
JMS08BA2WH General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burn box had rusted through under one burner.
-
John from Belle Plaine, MN
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers
With a nut driver removed the four heating element sockets (four small sheet metal screws) and the seventeen sheet metal screws that secured the burn box, removed the sheet metal box and inserted the new one. Not all the holes lined up at first for the screws, but starting in front with the four that did fit, the sheet metal gradually li
... Read more
ned itself up with all the other holes for a perfect fit.
Read less
Was this helpful?
Thank you for voting!
Drip bowls were rusty and not original GE. Small burners never fit quite right and rocked unevenly.
-
Ian from Casselberry, FL
- Easy
- 15 - 30 mins
Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in openin
... Read more
g and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The burner would not work.
-
Sue from Fort Oglethorpe, GA
- Easy
- 15 - 30 mins
-
Screw drivers
I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.
Was this helpful?
Thank you for voting!
Front and back burners not getting hot
-
Fred from De Leon, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.
Was this helpful?
Thank you for voting!
none to occasional power to burner elements
-
Mohammed from San Jose, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Exactly followed the instructional video and my installation was flawless. Now the burners power up and function like new. The whole repair was smooth and easy.
Was this helpful?
Thank you for voting!
plastic adapter was broken on end of the block kit
-
Michael from West Monroe, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas
Was this helpful?
Thank you for voting!
Burner not heating
-
Henry from Norwich, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.
Was this helpful?
Thank you for voting!
Broiler element would not heat
-
George from Fairport, NY
- Really Easy
- 15 - 30 mins
-
Socket set
After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worke
... Read more
d once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.
Read less
Was this helpful?
Thank you for voting!
Oven broiler stopped working. Had to replace the broiler element.
-
Don from Los Altos, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bott
... Read more
om and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.
Read less
Was this helpful?
Thank you for voting!
Replace Broiler Element
-
Mike from Davisburg, MI
- Easy
- 15 - 30 mins
-
Socket set
The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!
Was this helpful?
Thank you for voting!
Broiler element
-
Jess from Edmond, OK
- Very Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.
Was this helpful?
Thank you for voting!
Broiler element replaced as well as oven door seal.
-
---Tim from selma, NC
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to discon
... Read more
nect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
needed new drip bowls for stovetop GE
-
Patricia from Centereach, NY
- Really Easy
- Less than 15 mins
removed the burners and dropped the drip bowls in. Very easy to do,
Other Parts Used:
Was this helpful?
Thank you for voting!
the center of the element had broken
-
Betty from Fayetteville, WV
- Really Easy
- Less than 15 mins
just pulled the old one out and replaced with new one. very easy
Was this helpful?
Thank you for voting!
GE Electric Range rear left burner quit coming on
-
Richard from Richmond, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.
Was this helpful?
Thank you for voting!